USGS Science⌕ Search

Geology topics

R. S. Parker

Publications and source records attributed to R. S. Parker.

16 recordsLinked to original sources

Altered streamflow and sediment entrainment in the Gunnison Gorge

The Gunnison River in the Gunnison Gorge is a canyon river where upstream dams regulate mainstem discharge but do not affect debris-flow sediment supply from tributaries entering below the reservoirs. Regulation since 1966 has altered flood frequency, streambed mobility, and fluvial geomorphology creating potential resource-management issues. The duration of moderate streamflows between 32.3 and 85.0 m3/s has increased threefold since 1966. This, along with flood-peak attenuation, has facilitated fine-sediment deposition and vegetation encroachment on stream banks. The Shields equation and on-site channel geometry and bed-material measurements were used to assess changes in sediment entrainment in four alluvial reaches. Sand and fine gravel are transported through riffle/pool reaches at most discharges, but the cobbles and boulders composing the streambed in many reaches now are infrequently entrained. Periodic debris flows add coarse sediment to rapids and can increase pool elevation and the streambed area affected by backwater and fine-sediment accumulation. Debris-flow supplied boulders accumulate on fans and in rapids and constrict the channel until reworked by larger floods. The response to streamflow-regime changes in the Gunnison Gorge could serve as an analog for alluvial reaches in other regulated canyon rivers.

Journal of the American Water Resources Associatio↗

Spring census of mid-continent sandhill cranes using aerial infrared videography

Aerial infrared videography was used to map spatial distributions of nocturnal sandhill crane (Grus canadensis) flocks and determine crane densities within roosts as an alternative to the currently used diurnal photo-corrected ocular transect method to estimate the size of the mid-continental population. The densities determined from samples taken over the course of a night show variability. Densities measured early in the night (2100 to 2300 hrs) were generally lower than those measured in the time period after midnight and up until cranes prepared to depart their roosts before sunrise. This suggests that cranes may be more active early in the night and possibly still settling into their roosts at this time. For this reason, densities and areas measured later at night and into the early morning were used to estimate population size. Our methods estimated that the annual crane populations along the central Platte River in Nebraska were higher than estimates from the ocular transect method; however both methods showed a similar trend with time. Our population size estimates likely were higher because our methodology provided synoptic imagery of crane roosts along the entire study reach when all cranes had returned to the river, and the nocturnal densities were higher than previous estimates using observations from late evening or early morning. In addition to providing a tool for estimating annual population size, infrared videography can be utilized over time to identify spatial changes in the roosting patterns that may occur as a result of riverine management activities.

Journal of Wildlife Management↗

Assessing sandhill crane roosting habitatalong the Platte River, Nebraska

Each spring approximately 500,000 sandhill cranes and some endangered whooping cranes use the Central Platte River Valley in Nebraska as a staging habitat during their migration north to breeding and nesting grounds in Canada, Alaska, and the Siberian Arctic. Over the last century changes in the flow of the river have altered the river channels and the distribution of roost sites. USGS researchers studied linkages between water flow, sediment supply, channel morphology, and preferred sites for crane roosting. These results are useful for estimating crane populations and for providing resource managers with techniques to understand crane habitats.

Fact Sheet↗

Analysis and mapping of post-fire hydrologic hazards for the 2002 Hayman, Coal Seam, and Missionary Ridge wildfires, Colorado

Wildfires caused extreme changes in the hydrologic, hydraulic, and geomorphologic characteristics of many Colorado drainage basins in the summer of 2002. Detailed assessments were made of the short-term effects of three wildfires on burned and adjacent unburned parts of drainage basins. These were the Hayman, Coal Seam, and Missionary Ridge wildfires. Longer term runoff characteristics that reflect post-fire drainage basin recovery expected to develop over a period of several years also were analyzed for two affected stream reaches: the South Platte River between Deckers and Trumbull, and Mitchell Creek in Glenwood Springs. The 10-, 50-, 100-, and 500-year flood-plain boundaries and water-surface profiles were computed in a detailed hydraulic study of the Deckers-to-Trumbull reach. The Hayman wildfire burned approximately 138,000 acres (216 square miles) in granitic terrain near Denver, and the predominant potential hazard in this area is flooding by sediment-laden water along the large tributaries to and the main stem of the South Platte River. The Coal Seam wildfire burned approximately 12,200 acres (19.1 square miles) near Glenwood Springs, and the Missionary Ridge wildfire burned approximately 70,500 acres (110 square miles) near Durango, both in areas underlain by marine shales where the predominant potential hazard is debris-flow inundation of low-lying areas. Hydrographs and peak discharges for pre-burn and post-burn scenarios were computed for each drainage basin and tributary subbasin by using rainfall-runoff models because streamflow data for most tributary subbasins were not available. An objective rainfall-runoff model calibration method based on nonlinear regression and referred to as the ?objective calibration method? was developed and applied to rainfall-runoff models for three burned areas. The HEC-1 rainfall-runoff model was used to simulate the pre-burn rainfall-runoff processes in response to the 100-year storm, and HEC-HMS was used for runoff hydrograph generation. Post-burn rainfall-runoff parameters were determined by adjusting the runoff-curve numbers on the basis of a weighting procedure derived from the U.S. Soil Conservation Service (now the National Resources Conservation Service) equation for precipitation excess and the effect of burn severity. This weighting procedure was determined to be more appropriate than simple area weighting because of the potentially marked effect of even small burned areas on the runoff hydrograph in individual drainage basins. Computed water-peak discharges from HEC-HMS models were increased volumetrically to account for increased sediment concentrations that are expected as a result of accelerated erosion after burning. Peak discharge estimates for potential floods in the South Platte River were increased by a factor that assumed a volumetric sediment concentration (Cv) of 20 percent. Flood hydrographs for the South Platte River and Mitchell Creek were routed down main-stem channels using watershed-routing algorithms included in the HEC-HMS rainfall-runoff model. In areas subject to debris flows in the Coal Seam and Missionary Ridge burned areas, debris-flow discharges were simulated by 100-year rainfall events, and the inflow hydrographs at tributary mouths were simulated by using the objective calibration method. Sediment concentrations (Cv) used in debris-flow simulations were varied through the event, and were initial Cv 20 percent, mean Cv approximately 31 percent, maximum Cv 48 percent, Cv 43 percent at the time of the water hydrograph peak, and Cv 20 percent for the duration of the event. The FLO-2D flood- and debris-flow routing model was used to delineate the area of unconfined debris-flow inundation on selected alluvial fan and valley floor areas. A method was developed to objectively determine the post-fire recovery period for the Hayman and Coal Seam burned areas using runoff-curve numbers (RCN) for all drainage basins for a 50-year period. A

Scientific Investigations Report↗

Developing a post-fire flood chronology and recurrence probability from alluvial stratigraphy in the Buffalo Creek watershed, Colorado, USA

Stratigraphic and geomorphic evidence indicate floods that occur soon after forest fires have been intermittent but common events in many mountainous areas during the past several thousand years. The magnitude and recurrence of these post-fire flood events reflects the joint probability between the recurrence of fires and the recurrence of subsequent rainfall events of varying magnitude and intensity. Following the May 1996 Buffalo Creek, Colorado, forest fire, precipitation amounts and intensities that generated very little surface runoff outside of the burned area resulted in severe hillslope erosion, floods, and streambed sediment entrainment in the rugged, severely burned, 48 km2 area. These floods added sediment to many existing alluvial fans, while simultaneously incising other fans and alluvial deposits. Incision of older fans revealed multiple sequences of fluvially transported sandy gravel that grade upward into charcoal-rich, loamy horizons. We interpret these sequences to represent periods of high sediment transport and aggradation during floods, followed by intervals of quiescence and relative stability in the watershed until a subsequent fire occurred. An alluvial sequence near the mouth of a tributary draining a 0??82 km2 area indicated several previous post-fire flood cycles in the watershed. Dendrochronologic and radiocarbon ages of material in this deposit span approximately 2900 years, and define three aggradational periods. The three general aggradational periods are separated by intervals of approximately nine to ten centuries and reflect a 'millennium-scale' geomorphic response to a closely timed sequence of events: severe and intense, watershed-scale, stand-replacing fires and subsequent rainstorms and flooding. Millennium-scale aggradational units at the study site may have resulted from a scenario in which the initial runoff from the burned watershed transported and deposited large volumes of sediment on downstream alluvial surfaces and tributary fans. Subsequent storm runoff may have produced localized incision and channelization, preventing additional vertical aggradation on the sampled alluvial deposit for several centuries. Two of the millennium-scale aggradational periods at the study site consist of multiple gravel and loam sequences with similar radiocarbon ages. These closely dated sequences may reflect a 'multidecade-scale' geomorphic response to more frequent, but aerially limited and less severe fires, followed by rainstorms of relatively common recurrence. Published in 2001 by John Wiley and Sons, Ltd.

Hydrological Processes↗

Identifying trends in sediment discharge from alterations in upstream land use

Environmental monitoring is a primary reason for collecting sediment data. One emphasis of this monitoring is identification of trends in suspended sediment discharge. A stochastic equation was used to generate time series of annual suspended sediment discharges using statistics from gaging stations with drainage areas between 1606 and 1 805 230 km2. Annual sediment discharge was increased linearly to yield a given increase at the end of a fixed period and trend statistics were computed for each simulation series using Kendal's tau (at 0.05 significance level). A parameter was calculated from two factors that control trend detection time: (a) the magnitude of change in sediment discharge, and (b) the natural variability of sediment discharge. In this analysis the detection of a trend at most stations is well over 100 years for a 20% increase in sediment discharge. Further research is needed to assess the sensitivity of detecting trends at sediment stations.

Effects of scale on interpretation and management ↗

Simulation of streamflow in small drainage basins in the southern Yampa River basin, Colorado

Coal mining operations in northwestern Colorado commonly are located in areas that have minimal available water-resource information. Drainage-basin models can be a method for extending water-resource information to include periods for which there are no records or to transfer the information to areas that have no streamflow-gaging stations. To evaluate the magnitude and variability of the components of the water balance in the small drainage basins monitored, and to provide some method for transfer of hydrologic data, the U.S. Geological Survey 's Precipitation-Runoff Modeling System was used for small drainage basins in the southern Yampa River basin to simulate daily mean streamflow using daily precipitation and air-temperature data. The study area was divided into three hydrologic regions, and in each of these regions, three drainage basins were monitored. Two of the drainage basins in each region were used to calibrate the Precipitation-Runoff Modeling System. The model was not calibrated for the third drainage basin in each region; instead, parameter values were transferred from the model that was calibrated for the two drainage basins. For all of the drainage basins except one, period of record used for calibration and verification included water years 1976-81. Simulated annual volumes of streamflow for drainage basins used in calibration compared well with observed values; individual hydrographs indicated timing differences between the observed and simulated daily mean streamflow. Observed and simulated annual average streamflows compared well for the periods of record, but values of simulated high and low streamflows were different than observed values. Similar results were obtained when calibrated model parameter values were transferred to drainage basins that were uncalibrated. (USGS)

Colorado↗

Calibration of a dissolved-solids model for the Yampa River basin between Steamboat Springs and Maybell, northwestern Colorado

The cumulative effects of changes in dissolved solids from a number of coal mines are needed to evaluate effects on downstream water use. A model for determining cumulative effects of streamflow, dissolved-solids concentration, and dissolved-solids load was calibrated for the Yampa River and its tributaries in northwestern Colorado. The model uses accounting principles. It establishes nodes on the stream system and sums water quantity and quality from node to node in the downstream direction. The model operates on a monthly time step for the study period that includes water years 1976 through 1981. Output is monthly mean streamflow, dissolved-solids concentration, and dissolved-solids load. Streamflow and dissolved-solids data from streamflow-gaging stations and other data-collection sites were used to define input data sets to initiate and to calibrate the model. The model was calibrated at four nodes and generally was within 10 percent of the observed values. The calibrated model can compute changes in dissolved-solids concentration or load resulting from the cumulative effects of new coal mines or the expansion of old coal mines in the Yampa River basin. (USGS)

Water-Resources Investigations Report↗

Methods for hydrologic monitoring of surface mining in the central-western United States

The regulations promulgated pursuant to the Surface Mining Control and Reclamation Act require the monitoring of potentially impacted hydrologic systems before, during, and after mining operations. This report details characteristics and processes that commonly determine the most acceptable approaches to hydrologic monitoring in the arid and semiarid central-western United States. No single approach is best for all hydrologic systems; consideration of basin characteristics, regulatory requirements, and regional patterns in hydrologic systems is necessary in any well-designed monitoring program for hydrologic-impact assessment. This report describes processes and characteristics that control the surface and subsurface hydraulics, as well as the water quality, of typical hydrological systems being mined in the central-western United States. After a discussion of these processes and characteristics, three examples are presented that describe acceptable, but nonexclusive, approaches to hydrologic monitoring network design. (USGS)

Open-File Report↗

Calibration procedure for a daily flow model of small watersheds with snowmelt runoff in the Green River coal region of Colorado

A calibration procedure was developed for the U.S. Geological Survey 's Precipitation-Runoff Modeling System for watersheds in which snowmelt is the major contributor to runoff. The model uses daily values of air temperature and precipitation as input and the output is mean daily discharge. The procedure appears sufficient to calibrate both streamflow volume and the timing of mean daily discharge if other model parameters are reasonably estimated. Model structure and sensitivity analysis suggest that one of the most important parameters is the available water-holding capacity of the soil (SMAX). Changing this parameter through a series of iterations, the calibration procedure minimizes the error between observed and predicted annual discharge. The calibration suggests that the single parameter SMAX may be sufficient for optimizing both the volumes and the timing of runoff, assuming other model parameters are adequately estimated. Additional optimization on parameters sensitive to timing does not appear to improve prediction. This indicates that these parameters were estimated accurately prior to calibration. Further investigation is needed on more watersheds to determine SMAX 's ability to calibrate volume and timing with a constant set of other model parameter values.

Colorado↗

Summary of hydrologic information for the Denver coal region, Colorado

A literature review of available hydrologic information for the Denver coal region is presented. Where little information is available, data from the U.S. Geological Survey 's WATSTORE data base are summarized. The information is divided into three categories: surface water, surface water quality, and groundwater. Data generally are lacking on surface water and surface water quality. The effects of man 's activities on streamflow quantity and quality are not known. Considerable literature is available on the major aquifers in the area, but less is known about the shallow groundwater system. (USGS)

Water-Resources Investigations Report↗

Simulated effects of anticipated coal mining on dissolved solids in selected tributaries of the Yampa River, northwestern Colorado

Identifying cumulative effects of coal mining on dissolved solids downstream from multipe coal-mining operations is particularly important in western basins. The problem of identifying cumulative effects is evident in the Trout Creek drainage, a tributary to the Yampa River in northwestern Colorado, where a number of mines are active and mine expansions are planned. As an evaluation tool, a model was developed and calibrated for the Trout Creek drainage and a reach of the Yampa River main stem. This model uses a series of nodes on the stream network to sum water quantity and quality through the network. The model operates on a monthly basis and uses data from water years 1976 to 1981. Output is mean monthly discharge, dissolved-solids concentration, and dissolved-solids load. Observed data are needed to initiate the model and for model calibration. Some data were extrapolated from records of nearby streamflow-gaging stations. Some nodes within the stream network were for inputs from anticipated mining and were inactive during calibrations. After calibration, these nodes were used to input water discharge at a given dissolved-solids concentration to reflect various future mine configurations. (USGS)

Water-Resources Investigations Report↗

The Quality of Water Discharging From the New River and Clear Fork Basins, Tennessee

The quality of water discharging from a strip-mined basin and a relatively unmined basin on the Cumberland Plateau in Tennessee are examined and compared. The chemical and aesthetic quality of these waters will directly affect the chemical and aesthetic quality of the water flowing through a proposed national river and recreation area. Water from the heavily mined New River basin is characterized by neutral pH, low dissolved solids (less than 300 milligrams per liter), and high concentrations of suspended sediment. More than 90 percent of the suspended sediment is silt and clay. Suspended-sediment concentrations in the thousands of milligrams per liter are not uncommon for New River and often impart a highly turbid appearance to the water. Approximately 590,000 tons of suspended sediment were discharged from the New River basin in 1977, as compared to an estimated 20,000 tons from the relatively unmined Clear Fork basin. In association with these fine-grain suspended sediments are sorbed trace metals. In 1977 the New River basin discharged an estimated 17,000 tons of suspended iron while Clear Fork discharged an estimated 600 tons. Suspended-sediment concentration was found to be highly correlated with both suspended and total trace-metal concentrations. This correlation coupled with the nearly neutral pH of the water indicates that trace metals are transported primarily in the suspended phase. The most promising indicator of the presence of coal mining was found to be dissolved sulfate. All unmined basins sampled in this study showed dissolved sulfate concentrations less than 20 milligrams per liter, whereas all mined basins had dissolved-sulfate concentrations in excess of 20 milligrams per liter regardless of basin size or discharge.

Tennessee↗