Geology topics

Obaidul Haque

Publications and source records attributed to Obaidul Haque.

17 recordsLinked to original sources

USGS2023

ECCOE Landsat quarterly Calibration and Validation report—Quarter 4, 2022

Executive Summary The U.S. Geological Survey Earth Resources Observation and Science Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 4 (October–December) of 2022. All data used to compile the Cal/Val analysis results presented in this report are freely available from the U.S. Geological Survey EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the ECCOE Landsat Cal/Val Team closely monitored was the lowering of the Landsat 7 orbit. On April 6, 2022, the Landsat 7 Enhanced Thematic Mapper Plus (ETM+) sensor was placed into standby mode, and a series of spacecraft burns was completed through the month of April to lower the satellite’s orbit by 8 kilometers. Imaging resumed at a lower orbit of 697 kilometers on May 5, 2022, extending the science mission. Additional information about the Landsat 7 orbit lowering is here: https://www.usgs.gov/centers/eros/news/landsat-7-lowered-standard-landsat-orbit#:~:text=The%20satellite's%20primary%20science%20mission%20has%20ended&text=On%20April%206%2C%202022%2C%20the,satellite's%20orbit%20by%208%20kilometers .

Open-File Report↗

USGS2023

ECCOE Landsat quarterly Calibration and Validation report—Quarter 3, 2022

Executive Summary The U.S. Geological Survey Earth Resources Observation and Science Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 3 (July–September) of 2022. All data used to compile the Cal/Val analysis results presented in this report are freely available from the U.S. Geological Survey EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the ECCOE Landsat Cal/Val Team closely monitored was the lowering of the Landsat 7 orbit. On April 6, 2022, the Landsat 7 Enhanced Thematic Mapper Plus (ETM+) sensor was placed into standby mode, and a series of spacecraft burns was completed through the month of April to lower the satellite’s orbit by 8 kilometers. Imaging resumed at a lower orbit of 697 kilometers on May 5, 2022, extending the science mission to allow for essential data acquisition during the 2022 Northern Hemisphere fire and growing season. Additional information about the Landsat 7 orbit lowering is here: https://www.usgs.gov/centers/eros/news/landsat-7-lowered-standard-landsat-orbit#:~:text=The%20satellite's%20primary%20science%20mission%20has%20ended&text=On%20April%206%2C%202022%2C%20the,satellite's%20orbit%20by%208%20kilometers .

Open-File Report↗

USGS2022

ECCOE Landsat Quarterly Calibration and Validation report—Quarter 2, 2022

Executive Summary The U.S. Geological Survey Earth Resources Observation and Science Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 2 (April–June), 2022. All data used to compile the Cal/Val analysis results presented in this report are freely available from the U.S. Geological Survey EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the ECCOE Landsat Cal/Val Team closely monitored was the lowering of the Landsat 7 orbit. On April 6, 2022, the Landsat 7 Enhanced Thematic Mapper Plus (ETM+) sensor was placed into standby mode, and a series of spacecraft burns was completed throughout the month of April to lower the satellite’s orbit by 8 kilometers. Imaging resumed at the lower orbit of 697 kilometers on May 5, 2022, extending the science mission to allow for essential data to be acquired during the 2022 Northern Hemisphere fire and growing season. Additional information about the Landsat 7 orbit lowering is here: https://www.usgs.gov/centers/eros/news/landsat-7-lowered-standard-landsat-orbit#:~:text=The%20satellite's%20primary%20science%20mission%20has%20ended&text=On%20April%206%2C%202022%2C%20the,satellite's%20orbit%20by%208%20kilometers .

Open-File Report↗

USGS2022

ECCOE Landsat Quarterly Calibration and Validation report—Quarter 1, 2022

Executive Summary The U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 1 (January–March), 2022. All data used to compile the Cal/Val analysis results presented in this report are freely available from the USGS EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the Cal/Val Team continued to closely monitor this quarter was the Landsat 8 Thermal Infrared Sensor (TIRS) response degradation, which has been observed since the two November 2020 safehold events. Detailed analysis results characterizing this degradation have been included in this report. Additional information about the safehold events is here: https://www.usgs.gov/core-science-systems/nli/landsat/november-19-2020-landsat-8-data-availability-update-recent-safehold .

Open-File Report↗

USGS2022

ECCOE Landsat Quarterly Calibration and Validation report— Quarter 4, 2021

Executive Summary The U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 4 (October–December), 2021. All data used to compile the Cal/Val analysis results presented in this report are freely available from the USGS EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the Cal/Val Team continued to closely monitor this quarter was the Landsat 8 Thermal Infrared Sensor (TIRS) response degradation, which has been observed since the two November 2020 safehold events. Detailed analysis results characterizing this degradation have been included in this report. Additional information about the safehold events is here: https://www.usgs.gov/core-science-systems/nli/landsat/november-19-2020-landsat-8-data-availability-update-recent-safehold .

Open-File Report↗

USGS2022

ECCOE Landsat quarterly Calibration and Validation report—Quarter 3, 2021

Executive Summary The U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 3 (July–September), 2021. All data used to compile the Cal/Val analysis results presented in this report are freely available from the USGS EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the Cal/Val Team continued to closely monitor this quarter was the Landsat 8 Thermal Infrared Sensor (TIRS) response degradation, which has been observed since the two November 2020 safehold events. Detailed analysis results characterizing this degradation have been included in this report. Additional information about the safehold events is here: https://www.usgs.gov/core-science-systems/nli/landsat/november-19-2020-landsat-8-data-availability-update-recent-safehold .

Open-File Report↗

USGS2021

ECCOE Landsat quarterly Calibration and Validation report — Quarter 2, 2021

Executive Summary The U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 7–8 for quarter 2 (April–June), 2021. All data used to compile the Cal/Val analysis results presented in this report are freely available from the USGS EarthExplorer website: https://earthexplorer.usgs.gov . One specific activity that the Cal/Val Team continued to closely monitor this quarter was the Landsat 8 Thermal Infrared Sensor (TIRS) response degradation, which has been observed since the two November 2020 safehold events. Detailed analysis results characterizing this degradation have been included in this report. Additional information about the safehold events is here: https://www.usgs.gov/core-science-systems/nli/landsat/november-19-2020-landsat-8-data-availability-update-recent-safehold .

Open-File Report↗

USGS2019

Landsat 1-5 Multispectral Scanner System (MSS) sensors radiometric calibration update

First launched in 1972, the Landsat satellite sensors have provided the longest continuous record of high quality images of the Earth’s surface that are used in both civilian and military applications. The Landsat Multispectral Scanner (MSS) sensor was on-board Landsat-1 through Landsat-5. In fact, the MSS sensors provide the only systematic global multispectral space-based imagery of the Earth’s surface from 1972 to 1982. This paper focuses on the radiometric calibration update of the Landsat 1-5 MSS sensors. The radiometric calibration was performed in both radiance and reflectance-based scales through cross-calibration approach. Simultaneous or a near simultaneous image collections were available for MSS sensor pairs and used for the cross-calibration. The estimated uncertainties for this calibration update exhibit progressively decreasing calibration accuracy, ranging from 5.1% for MSS 5 to 8.8% for MSS-1 in the Green spectral band, for example. Lastly, the new radiometric calibration coefficients were validated through the use of pseudo invariant calibration sites (PICS). The temporal TOA Radiance and TOA Reflectance over the Sonoran Desert were plotted with the purpose of verifying the lifetime radiometric stability of MSS sensors. With the previous calibration, the agreement between the measurements of TOA Reflectance over the Sonoran Desert was around 7.5% for all spectral bands. With the calibration update implemented in this study, the agreement between MSS sensors is 3.6%, 2.9%, 3.5% and 5.9% for the Green, Red, NIR-1 and NIR 2 spectral bands, respectively. This study ties all the Landsat legacy instruments from Landsat-1 MSS through Landsat-8 OLI to a consistent radiometric scale.

IEEE Transactions on Geoscience and Remote Sensing↗

USGS2018

Landsat-8 on-orbit and Landsat-9 pre-launch sensor radiometric characterization

Landsat-8 has been operating on-orbit for 5+ years. Its two sensors, the Operational Land Imager (OLI) and Thermal Infrared Sensor (TIRS), are continuing to produce high quality data. The OLI has been radiometrically stable at the better than 0.3% level on a band average basis for all but the shortest wavelength (443 nm) band, which has degraded about 1.3% since launch. All on-board calibration devices continue to perform well and consistently. No gaps in across track coverage exist as 100% operability of the detectors is maintained. The variability over time of detector responsivity within a band relative to the average is better than 0.05% (1 sigma), though there are occasional detectors that jump up to 1.5% in response in the Short-Wave InfraRed (SWIR) bands. Signal-to-Noise performance continues at 2-3x better than requirements, with a small degradation in the 443 nm band commensurate with the loss in sensitivity. Pre-launch error analysis, combined with the stability of the OLI indicates that the absolute reflectance calibration uncertainty is better than 3%; comparisons to ground measurements and comparisons to other sensors are consistent with this. The Landsat-8 TIRS is similarly radiometrically stable, showing changes of at most 0.3% over the mission. The uncertainty in the absolute calibration as well as the detector to detector variability are largely driven by the stray light response of TIRS. The current processing corrects most of the stray light effects, resulting in absolute uncertainties of ~1% and reduced striping. Efforts continue to further reduce the striping. Noise equivalent delta temperature is about 50 mK at typical temperatures and 100% detector operability is maintained. Landsat-9 is currently under development with a launch no earlier than December 2020. The nearly identical OLI-2 and upgraded TIRS-2 sensors have completed integration and are in the process of instrument level performance characterization including spectral, spatial, radiometric and geometric testing. Component and assembly level measurements of the OLI-2, which include spectral response, radiometric response and stray light indicate comparable performance to OLI. The first functional tests occurred in July 2018 and spatial performance testing in vacuum is scheduled for August 2018. Similarly, for TIRS-2, partially integrated instrument level testing indicated spectral and spatial responses comparable to TIRS, with stray light reduced by approximately an order of magnitude from TIRS.

Conference Paper↗

USGS2018

Sentinel-2A MSI and Landsat-8 OLI radiometric cross comparison over desert sites

The Sentinel-2A and Landsat-8 satellites carry on-board moderate resolution multispectral imagers for the purpose of documenting the Earth’s changing surface. Though they are independently built and managed, users will certainly take advantage of the opportunity to have higher temporal coverage by combining the datasets. Thus it is important for the radiometric and geometric calibration of the MultiSpectral Instrument (MSI) and the Operational Land Imager (OLI) to be compatible. Cross-calibration of MSI to OLI has been accomplished using multiple techniques involving the use of pseudo-invariant calibration sites (PICS) using direct comparisons as well as through use of PICS models predicting top-of-atmosphere reflectance. A team from the University of Arizona is acquiring field data under both instruments for vicarious calibration of the sensors. This paper shows that the work done to date by the Landsat and Sentinel-2 calibration teams has resulted in stable radiometric calibration for each instrument and consistency to ~2.5% between the instruments for all the spectral bands that the instruments have in common.

European Journal of Remote Sensing↗

USGS2017

Radiometric characterization of Landsat Collection 1 products

Landsat data in the U.S. Geological Survey (USGS) archive are being reprocessed to generate a tiered collection of consistently geolocated and radiometrically calibrated products that are suitable for time series analyses. With the implementation of the collection management, no major updates will be made to calibration of the Landsat sensors within a collection. Only calibration parameters needed to maintain the established calibration trends without an effect on derived environmental records will be regularly updated, while all other changes will be deferred to a new collection. This first collection, Collection 1, incorporates various radiometric calibration updates to all Landsat sensors including absolute and relative gains for Landsat 8 Operational Land Imager (OLI), stray light correction for Landsat 8 Thermal Infrared Sensor (TIRS), absolute gains for Landsat 4 and 5 Thematic Mappers (TM), recalibration of Landsat 1-5 Multispectral Scanners (MSS) to ensure radiometric consistency among different formats of archived MSS data, and a transfer of Landsat 8 OLI reflectance based calibration to all previous Landsat sensors. While all OLI/TIRS, ETM+ and majority of TM data have already been reprocessed to Collection 1, a completion of MSS and remaining TM data reprocessing is expected by the end of this year. It is important to note that, although still available for download from the USGS web pages, the products generated using the Pre-Collection processing do not benefit from the latest radiometric calibration updates. In this paper, we are assessing radiometry of solar reflective bands in Landsat Collection 1 products through analysis of trends in on-board calibrator and pseudo invariant site (PICS) responses.

Conference Paper↗

USGS2016

Landsat-7 ETM+ radiometric calibration status

Now in its 17th year of operation, the Enhanced Thematic Mapper + (ETM+), on board the Landsat-7 satellite, continues to systematically acquire imagery of the Earth to add to the 40+ year archive of Landsat data. Characterization of the ETM+ on-orbit radiometric performance has been on-going since its launch in 1999. The radiometric calibration of the reflective bands is still monitored using on-board calibration devices, though the Pseudo-Invariant Calibration Sites (PICS) method has proven to be an effective tool as well. The calibration gains were updated in April 2013 based primarily on PICS results, which corrected for a change of as much as -0.2%/year degradation in the worst case bands. A new comparison with the SADE database of PICS results indicates no additional degradation in the updated calibration. PICS data are still being tracked though the recent trends are not well understood. The thermal band calibration was updated last in October 2013 based on a continued calibration effort by NASA/Jet Propulsion Lab and Rochester Institute of Technology. The update accounted for a 0.036 W/m 2 sr μm or 0.26K at 300K bias error. The updated lifetime trend is now stable to within +/- 0.4K.

Conference Paper↗

USGS2016

Radiometric calibration updates to the Landsat collection

The Landsat Project is planning to implement a new collection management strategy for Landsat products generated at the U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Center. The goal of the initiative is to identify a collection of consistently geolocated and radiometrically calibrated images across the entire Landsat archive that is readily suitable for time-series analyses. In order to perform an accurate land change analysis, the data from all Landsat sensors must be on the same radiometric scale. Landsat 7 Enhanced Thematic Mapper Plus (ETM+) is calibrated to a radiance standard and all previous sensors are cross-calibrated to its radiometric scale. Landsat 8 Operational Land Imager (OLI) is calibrated to both radiance and reflectance standards independently. The Landsat 8 OLI reflectance calibration is considered to be most accurate. To improve radiometric calibration accuracy of historical data, Landsat 1-7 sensors also need to be cross-calibrated to the OLI reflectance scale. Results of that effort, as well as other calibration updates including the absolute and relative radiometric calibration and saturated pixel replacement for Landsat 8 OLI and absolute calibration for Landsat 4 and 5 Thematic Mappers (TM), will be implemented into Landsat products during the archive reprocessing campaign planned within the new collection management strategy. This paper reports on the planned radiometric calibration updates to the solar reflective bands of the new Landsat collection.

Conference Paper↗

USGS2014

Radiometric cross calibration of Landsat 8 Operational Land Imager (OLI) and Landsat 7 Enhanced Thematic Mapper Plus (ETM+)

This study evaluates the radiometric consistency between Landsat-8 Operational Land Imager (OLI) and Landsat 7 Enhanced Thematic Mapper Plus (ETM+) using cross calibration techniques. Two approaches are used, one based on cross calibration between the two sensors using simultaneous image pairs, acquired during an underfly event on 29–30 March 2013. The other approach is based on using time series of image statistics acquired by these two sensors over the Libya 4 pseudo invariant calibration site (PICS) (+28.55°N, +23.39°E). Analyses from these approaches show that the reflectance calibration of OLI is generally within ±3% of the ETM+ radiance calibration for all the reflective bands from visible to short wave infrared regions when the ChKur solar spectrum is used to convert the ETM+ radiance to reflectance. Similar results are obtained comparing the OLI radiance calibration directly with the ETM+ radiance calibration and the results in these two different physical units (radiance and reflectance) agree to within ±2% for all the analogous bands. These results will also be useful to tie all the Landsat heritage sensors from Landsat 1 MultiSpectral Scanner (MSS) through Landsat-8 OLI to a consistent radiometric scale.

Remote Sensing↗

USGS2013

Radiometric and geometric assessment of data from the RapidEye constellation of satellites

To monitor land surface processes over a wide range of temporal and spatial scales, it is critical to have coordinated observations of the Earth's surface using imagery acquired from multiple spaceborne imaging sensors. The RapidEye (RE) satellite constellation acquires high-resolution satellite images covering the entire globe within a very short period of time by sensors identical in construction and cross-calibrated to each other. To evaluate the RE high-resolution Multi-spectral Imager (MSI) sensor capabilities, a cross-comparison between the RE constellation of sensors was performed first using image statistics based on large common areas observed over pseudo-invariant calibration sites (PICS) by the sensors and, second, by comparing the on-orbit radiometric calibration temporal trending over a large number of calibration sites. For any spectral band, the individual responses measured by the five satellites of the RE constellation were found to differ <2–3% from the average constellation response depending on the method used for evaluation. Geometric assessment was also performed to study the positional accuracy and relative band-to-band (B2B) alignment of the image data sets. The position accuracy was assessed by comparing the RE imagery against high-resolution aerial imagery, while the B2B characterization was performed by registering each band against every other band to ensure that the proper band alignment is provided for an image product. The B2B results indicate that the internal alignments of these five RE bands are in agreement, with bands typically registered to within 0.25 pixels of each other or better.

International Journal of Remote Sensing↗

USGS2008

Landsat 5 Thematic Mapper (TM) recalibration procedure for data processed using the National Landsat Archive Production System (NLAPS)

The multispectral data from the Landsat 5 (L5) Thematic Mapper (TM) sensor provides the backbone of an extensive archive of moderate resolution Earth imagery. Even after more than 24 years of service, the L5 TM is still operational. Given the longevity of the instrument, the detectors have aged, and the system's radiometric characteristics have changed since launch. The calibration procedures and parameters in National Land Archive Production System (NLAPS) have also changed with time. Revised radiometric calibrations in 2003 and 2007 have improved the radiometric accuracy of recently processed data; however, users with data processed prior to the calibration update have not benefited from these revisions. A general procedure has been developed to give users the ability to recalibrate their existing systematically corrected (Level-1) products. The best recalibration can be obtained if the work order report originally used in product generation is still available. This paper discusses the procedure to recalibrate the L5 TM data for the users who have the work order files that were delivered with their products.

Conference Paper↗

USGS2008

Development of Landsat-5 thematic mapper internal calibrator gain and offset table

The National Landsat Archive Production System (NLAPS) has been the primary processing system for Landsat data since U.S. Geological Survey (USGS) Earth Resources Observation and Science Center (EROS) started archiving Landsat data. NLAPS converts raw satellite data into radiometrically and geometrically calibrated products. NLAPS has historically used the Internal Calibrator (IC) to calibrate the reflective bands of the Landsat-5 Thematic Mapper (TM), even though the lamps in the IC were less stable than the TM detectors, as evidenced by vicarious calibration results. In 2003, a major effort was made to model the actual TM gain change and to update NLAPS to use this model rather than the unstable IC data for radiometric calibration. The model coefficients were revised in 2007 to reflect greater understanding of the changes in the TM responsivity. While the calibration updates are important to users with recently processed data, the processing system no longer calculates the original IC gain or offset. For specific applications, it is useful to have a record of the gain and offset actually applied to the older data. Thus, the NLAPS calibration database was used to generate estimated daily values for the radiometric gain and offset that might have been applied to TM data. This paper discusses the need for and generation of the NLAPS IC gain and offset tables. A companion paper covers the application of and errors associated with using these tables.

Conference Paper↗