Michael Rymer | USGS Science

USGS2021

A revised position for the primary strand of the Pleistocene-Holocene San Andreas fault in southern California

The San Andreas fault has the highest calculated time-dependent probability for large-magnitude earthquakes in southern California. However, where the fault is multistranded east of the Los Angeles metropolitan area, it has been uncertain which strand has the fastest slip rate and, therefore, which has the highest probability of a destructive earthquake. Reconstruction of offset Pleistocene-Holocene landforms dated using the uranium-thorium soil carbonate and beryllium-10 surface exposure techniques indicates slip rates of 24.1 ± 3 millimeter per year for the San Andreas fault, with 21.6 ± 2 and 2.5 ± 1 millimeters per year for the Mission Creek and Banning strands, respectively. These data establish the Mission Creek strand as the primary fault bounding the Pacific and North American plates at this latitude and imply that 6 to 9 meters of elastic strain has accumulated along the fault since the most recent surface-rupturing earthquake, highlighting the potential for large earthquakes along this strand.

California↗

USGS2020

San Andreas fault exploration using refraction tomography and S-wave-type and Fϕ-mode guided waves

Surface ruptures from the 18 April 1906 M∼7.9 San Francisco earthquake were distributed over an ∼35 ‐meter‐wide zone at San Andreas Lake on the San Francisco Peninsula in California ( Schussler, 1906 ). Since ∼1906⁠ , the surface ruptures have been largely covered by water, but with water levels at near‐historic low levels in 2008–2011, we observed that the 1906 surface ruptures were no longer visible. As a fault imaging test, we acquired refraction tomography and guided‐wave data across the 1906 surface ruptures in 2011. We found that individual fault traces, as mapped by Schussler (1906) , can be identified on the basis of discrete low‐velocity zones ( ⁠V S and V P⁠ , reduced ∼40% and ∼34%⁠ , respectively) and high‐amplitude guided waves. Guided waves have traditionally been observed as large‐amplitude waveforms over wide (hundreds of meters to kilometers) zones of faulting, but we demonstrate that by evaluating guided waves (including Rayleigh/Love‐ and P / SV ‐types) in terms of peak ground velocity (PGV), individual near‐surface fault traces within a fault zone can be precisely located, even more than 100 yr after the surface ruptures. Such precise exploration can be used to focus paleoseismic trenching efforts and to identify or exclude faulting at specific sites. We evaluated PGV of both S ‐wave‐type and Fϕ ‐mode‐type guided waves and found that both wave types can be used to identify subsurface fault traces. At San Andreas Lake (main fault), S ‐wave‐type guided waves travel up to 18% slower than S body waves, and Fϕ ‐mode guided waves travel ∼60% slower than P body waves but ∼15% faster than S body waves. We found that guided‐wave amplitudes vary with frequency but are up to five times higher than those of body waves, including the S wave. Our data are consistent with the concept that guided waves can be a strong‐shaking hazard during large‐magnitude earthquakes.

Calfornia↗

USGS2011

Seismic calibration shots conducted in 2009 in the Imperial Valley, southern California, for the Salton Seismic Imaging Project (SSIP)

Rupture of the southern section of the San Andreas Fault, from the Coachella Valley to the Mojave Desert, is believed to be the greatest natural hazard facing California in the near future. With an estimated magnitude between 7.2 and 8.1, such an event would result in violent shaking, loss of life, and disruption of lifelines (freeways, aqueducts, power, petroleum, and communication lines) that would bring much of southern California to a standstill. As part of the Nation's efforts to prevent a catastrophe of this magnitude, a number of projects are underway to increase our knowledge of Earth processes in the area and to mitigate the effects of such an event. One such project is the Salton Seismic Imaging Project (SSIP), which is a collaborative venture between the United States Geological Survey (USGS), California Institute of Technology (Caltech), and Virginia Polytechnic Institute and State University (Virginia Tech). This project will generate and record seismic waves that travel through the crust and upper mantle of the Salton Trough. With these data, we will construct seismic images of the subsurface, both reflection and tomographic images. These images will contribute to the earthquake-hazard assessment in southern California by helping to constrain fault locations, sedimentary basin thickness and geometry, and sedimentary seismic velocity distributions. Data acquisition is currently scheduled for winter and spring of 2011. The design and goals of SSIP resemble those of the Los Angeles Region Seismic Experiment (LARSE) of the 1990's. LARSE focused on examining the San Andreas Fault system and associated thrust-fault systems of the Transverse Ranges. LARSE was successful in constraining the geometry of the San Andreas Fault at depth and in relating this geometry to mid-crustal, flower-structure-like decollements in the Transverse Ranges that splay upward into the network of hazardous thrust faults that caused the 1971 M 6.7 San Fernando and 1987 M 5.9 Whittier Narrows earthquakes. The project also succeeded in determining the depths and seismic-velocity distributions of several sedimentary basins, including the Los Angeles Basin, San Fernando Valley, and Antelope Valley. These results advanced our ability to understand and assess earthquake hazards in the Los Angeles region. In order to facilitate permitting and planning for the data collection phase of SSIP, in June of 2009 we set off calibration shots and recorded the seismic data with a variety of instruments at varying distances. We also exposed sections of buried clay drainage pipe near the shot points to determine the effect of seismic energy on the pipes. Clay drainage pipes are used by the irrigation districts in both the Coachella and Imperial Valleys to prevent ponding and remove salts and irrigation water. This report chronicles the calibration project. We present new near-source velocity data that are used to test the regression curves that were determined for the LARSE project. These curves are used to create setback tables to determine explosive charge size and for placement of shot points. We also found that our shots did not damage the irrigation pipes and that the ODEX drilling system did well in the clay rich soils of the Imperial Valley.

California↗