Geology topics

Kevin M. Lee

Publications and source records attributed to Kevin M. Lee.

4 recordsLinked to original sources

USGS2024

Direct measurements of sediment geoacoustic properties in the New England Mud Patch and shelf break

This paper reports on an original set of direct sound speed measurements collected with the acoustic coring system in the New England Mud Patch (NEMP) and shelf break area to the south. Cores collected within the NEMP show range-dependence of the mud with slower sound speed and lower attenuation on the west side. In the shelf break region, the highest sound speeds are observed between the 200- and 350-m isobaths. The depth-dependence of the mud layer in the NEMP includes a surficial layer with a negative sound speed gradient of 28 s −1 . The remainder of the mud column has a weak positive sound speed gradient of 6.2 s −1 over an isovelocity layer. Comparison between in situ and ex situ sound speed measurements provides an assessment of the effects of sediment disturbance from gravity coring operations. Small differences in the upper 2.5 m were attributed to the changes in the geoacoustic properties caused by disturbance from the coring process. Below 2.5 m, the average difference is close to zero, suggesting that these sediments were minimally disturbed. Finally, an in situ measurement of shear speed was obtained near the depth of maximum penetration. The shear speed was well correlated with sound speed from approximately the same depth interval.

New England Mud Patch↗

USGS2022

Measurements of Geologic Characteristics and Geophysical Properties of Sediments From the New England Mud Patch

The characterization of physical, geological, and geophysical properties of sediments within the New England Mud Patch (NEMP) was undertaken to provide a physical basis for acoustic inversions associated with the SeaBed Characterization EXperiment 2017 (SBCEX17). Using a suite of 89 sediment cores (piston/trigger, gravity [acoustic], and vibracore), a comprehensive database of laboratory-based sediment analyses, geophysical core logs, and the results of seismic reflection profiling, we formulate a three-layer lithostratigraphic model of the area within and immediately adjacent to the SBCEX17 focus area, referred to as the seabed experiment area (SEA). The uppermost lithostratigraphic unit, Unit 1, is relatively homogenous clayey- to sandy silt, with consistent downcore textural, mineralogical, and physical property attributes. Unit 2 is a variable-thickness transitional layer between Unit 1 and Unit 3, whose properties reflect a decrease in proximal erosion and transition to a lower energy depositional environment. Unit 3 is clean quartz sand containing abundant shells and shell fragments that was regionally deposited during Holocene sea-level rise. 210 Pb and 14 C radiocarbon geochronologies spanning the past 13 000 years are used to facilitate intercore comparison across the SEA. Analytical results and laboratory methods used in the derivation of those results are described in detail, serving as a reference for ongoing and future investigation of the SEA and entire NEMP. Although the derived lithostratigraphic model of the SEA is in good agreement with past evaluations of the regional sedimentology, comparisons of the lithostratigraphic and seismostratigraphic models highlight several significant incompatibilities that remain to be satisfactorily explained.

IEEE Journal of Ocean Engineering↗

USGS2020

In situ measurements of compressional wave speed during gravity coring operations in the New England mud patch

This paper presents measurements of sediment sound-speed profiles measured in situ using the acoustic coring system (ACS). The reported measurements were obtained from seven gravity cores collected in the New England Mud Patch. The ACS uses two sets of transducers mounted below the penetrating tip of a sediment corer to make in situ measurements of geoacoustic properties as the corer penetrates the seabed. The in situ sound-speed profiles are interpreted in the context of stratigraphic layering measured by a seismic survey, and the measured sound-speed profiles are consistent with the geophysical description. The in situ sound-speed profiles measured by the ACS were compared to conventional measurements of sound speed on the recovered cores using the multisensor core logger (MSCL). The MSCL data displayed both random and systematic errors that were attributed to disturbance from the coring process and/or the handling of the sediments after collection. Finally, using porosity and grain size distributions measured from discrete samples of the cored sediments, the in situ sound-speed measurements were compared to empirical regressions based on independent data sets.

Atlantic Ocean, New England Mud Patch↗

USGS2015

Unusually loud ambient noise in tidewater glacier fjords: a signal of ice melt

In glacierized fjords, the ice-ocean boundary is a physically and biologically dynamic environment that is sensitive to both glacier flow and ocean circulation. Ocean ambient noise offers insight into processes and change at the ice-ocean boundary. Here we characterize fjord ambient noise and show that the average noise levels are louder than nearly all measured natural oceanic environments (significantly louder than sea ice and non-glacierized fjords). Icy Bay, Alaska has an annual average sound pressure level of 120 dB (re 1 μPa) with a broad peak between 1000 and 3000 Hz. Bubble formation in the water column as glacier ice melts is the noise source, with variability driven by fjord circulation patterns. Measurements from two additional fjords, in Alaska and Antarctica, support that this unusually loud ambient noise in Icy Bay is representative of glacierized fjords. These high noise levels likely alter the behavior of marine mammals.

Alaska↗