USGS Science⌕ Search

Geology topics

James F. Gibbs

Publications and source records attributed to James F. Gibbs.

At least 19 recordsLinked to original sources
USGS2020

Damping values derived from surface-source, downhole-receiver measurements at 22 sites in the San Francisco Bay Area of central California and the San Fernando Valley of southern California

A method discussed in Gibbs, Boore, et al. (1994) was applied to surface‐source, downhole‐receiver recordings at 22 boreholes, in the San Francisco Bay area in central California and the San Fernando Valley of southern California, to determine the average damping ratio of shear waves over depth intervals ranging from about 10 m to as much as 245 m (at one site), with most maximum depths being between 35 and 90 m. The average damping values range from somewhat less than 1% to almost 8%, with little dependence on grain size for sites in sediments. Surprisingly, the average damping values for sites with average velocities greater than about 450    m / s "> 450 m / s 450 m/s ⁠ , including, but not limited to rock sites, are generally larger than for sites with lower average velocities. The combined effect of the higher damping and shorter travel times through the rock columns, however, leads to an effective attenuation that is generally comparable or smaller than for soil sites.

California↗
USGS2002

Borehole velocity measurements at five sites that recorded the Cape Mendocino, California earthquake of 25 April, 1992

The U.S. Geological Survey (USGS), as part of an ongoing program to acquire seismic velocity and geologic data at locations that recorded strong-ground motions during earthquakes, has investigated five sites in the Fortuna, California region (Figure 1). We selected drill sites at strong-motion stations that recorded high accelerations (Table 1) from the Cape Mendocino earthquake (M 7.0) of 25 April 1992 (Oppenheimer et al., 1993). The boreholes were drilled to a nominal depth of 95 meters (310 ft) and cased with schedule 80 pvc-casing grouted in place at each location. S-wave and P-wave data were acquired at each site using a surface source and a borehole three-component geophone. This report contains the velocity models interpreted from the borehole data and gives reference to locations and peak accelerations at the selected strong-motion stations.

California↗
USGS2001

Borehole P- and S-wave velocity at thirteen stations in Southern California

The U.S. Geological Survey (USGS), as part of a program to acquire seismic velocity data at locations of strong-ground motion in earthquakes (e.g., Gibbs et al., 2000), has investigated thirteen additional sites in the Southern California region. Of the thirteen sites, twelve are in the vicinity of Whittier, California, and one is located in San Bernardino, California. Several deployments of temporary seismographs were made after the Whittier Narrows, California earthquake of 1 October 1987 (Mueller et al., 1988). A deployment, between 2 October and 9 November 1987, was the motivation for selection of six of the drill sites. Temporary portable seismographs at Hoover School (HOO), Lincoln School (LIN), Corps of Engineers Station (NAR), Olive Junior High School (OLV), Santa Anita Golf Course (SAG), and Southwestern Academy (SWA) recorded significant aftershock data. These portable sites, with the exception of Santa Anita Golf Course, were co-sited with strong-motion recorders. Stations at HOO, Lincoln School Whittier (WLB), Saint Paul High School (STP), Alisos Adult School (EXC), Cerritos College Gymnasium (CGM), Cerritos College Physical Science Building (CPS), and Cerritos College Police Building (CPB) were part of an array of digital strong-motion stations deployed from "bedrock" in Whittier to near the deepest part of the Los Angeles basin in Norwalk. Although development and siting of this new array (partially installed at the time of this writing) was generally motivated by the Whittier Narrows earthquake, these new sites (with the exception of HOO) were not part of any Whittier Narrows aftershock deployments. A similar new digital strong-motion site was installed at the San Bernardino Fire Station during the same time frame. Velocity data were obtained to depths of about 90 meters at two sites, 30 meters at seven sites, and 18 to 25 meters at four sites. Lithology data from the analysis of cuttings and samples was obtained from the two 90-meter deep holes and from five of the shallower holes to supplement the velocity interpretation. The two 90-meter boreholes (SB1, CPB) have been instrumented with borehole seismometers for continuous monitoring of earthquake activity (Rogers et al., 1998). No drill samples or cuttings were obtained from the other six sites, but driller's logs were scanned for major changes noted there. The velocity models at those sites were interpreted using only the measured data and major changes in the driller's log as noted above. The sites are shown in Figure 1 and listed in Table 1, which gives references to information regarding the strong-motion data. Several hundred strong-motion records of the main-shock were written by this moderate size earthquake (ML = 5.9), making it important from a scientific and engineering prospective (Brady et al., 1988; Shakal et al., 1988).

California↗
USGS1994

The attenuation of seismic shear waves in quaternary alluvium in Santa Clara Valley, California

We used shear waves, generated by an air-powered source at the ground surface and recorded in a borehole, to estimate the shear-wave quality factor at strong-motion station Gilroy no. 2. We find similar values of Q using both the decay of the spectra with depth and the slope of the spectral ratio at two depths; we find no evidence of a frequency dependence of Q . The mean value of Q over the depth range 10 to 115 m is close to 10. The use of this value over the depth of the borehole and the observed travel time of 0.358 sec gives a cumulative attenuation factor t * of 0.036 sec for the upper 180 m of the Quaternary alluvium. This is comparable to the differential decay between Gilroy no. 2 and a rock site 1.9 km away (Gilroy no. 1), as measured from the decay of the high-frequency spectra of accelerograms from large earthquakes, plotted on a log-linear scale: t * = 0.05, 0.04, and 0.03 sec for the 1979 Coyote Lake, 1984 Morgan Hill, and 1989 Loma Prieta earthquakes, respectively. The similarity between the attenuations measured from the low-strain surface source and those from the larger amplitude earthquake sources suggests that increases of damping due to nonlinear wave propagation effects are limited.

California↗
USGS1994

Seismic velocities and geologic logs from boreholes at three downhole arrays in San Francisco, California

The Loma Prieta earthquake of October 17, 1989 (1704 PST), has reinforced observations made by Wood and others (1908) after the 1906 San Francisco earthquake, that poor ground conditions (soft soil) increase the likelihood of shaking damage to structures. Since 1908 many studies (for example Borcherdt, 1970, Borcherdt and Gibbs, 1976, Borcherdt and Glassmoyer, 1992) have shown that soft soils amplify seismic waves at frequencies that can be damaging to structures. Damage in the City of San Francisco from the Loma Prieta earthquake was concentrated in the Marina District, the Embarcadero, and the China Basin areas. Each of these areas, to some degree, is underlain by soft soil deposits. These concentrations of damage raise important questions regarding the amplification effects of such deposits at damaging levels of motion. Unfortunately, no strong-motion recordings were obtained in these areas during the Loma Prieta earthquake and only a limited number (< 10) have been obtained on other soft soil sites in the United States. Consequently, important questions exist regarding the response of such deposits during damaging earthquakes, especially questions regarding the nonlinear soil response. Towards developing a data set to address these important questions, borehole strong-motion arrays have been installed at three locations. These arrays consist of groups of wide-dynamic-range pore-pressure transducers and three-component accelerometers, the outputs of which are recorded digitally. The arrays are designed to provide an integrated set of data on ground shaking, liquifaction-induced ground failure, and structural response. This report describes the detailed geologic, seismic, and material-property determinations derived at each of these sites.

California↗
USGS1989

Seismic velocities and attenuation from borehole measurements near the Parkfield prediction zone, Central California

Shear (S)- and compressional (P)- wave velocities were measured to a depth of 195 m in a borehole near the San Andreas fault where a recurrence of a moderate Parkfield earthquake is predicted. S-wave velocities determined from orthogonal directions of the S-wave source show velocity differences of approximately 20 percent. An average shear-wave Q of 4 was determined in relatively unconsolidated sands and gravels of the Paso Robles Formation in the depth interval 57.5-102.5 m.

Earthquake Spectra↗
USGS1980

In-situ measurements of seismic velocity at 27 locations in the Los Angeles, California region

Studies conducted in the San Francisco Bay Region (Gibbs, Fumal and Borcherdt, 1980) have shown that average shear-wave velocity can be readily tied to quantitative estimates of ground motion such as ground amplification and earthquake intensity. Furthermore, when certain physical properties of the geologic materials such as texture, hardness and fracture spacing are observed during geologic mapping, a method can be used to predict shear-wave velocity from the descriptions of geologic units. By measuring shear-wave velocities in key units together with the above data, regional maps depicting the earthquake shaking hazard can be compiled. The goals of the current program are to provide shear-wave data in the Los Angeles area to compare with that in the San Francisco Bay Region where high-strain intensity data are available. Data from twenty-seven locations are summarized in this report as part of a continuing project to seismically zone the Los Angeles area.

California↗
USGS1977

In-situ measurements of seismic velocities in the San Francisco Bay Region; part III

Seismic wave velocities (compressional and shear) are important parameters for estimating the seismic response characteristics of various geologic units when subjected to strong earthquake ground shaking. Seismic velocities of various units often show a strong correlation with the amounts of damage following large earthquakes and have been used as a basis for certain types of seismic zonation studies. In the current program seismic velocities have been measured at 59 locations 1n the San Francisco Bay Region. This report is the third in a series of Open-File Reports and describes the in-situ velocity measurements at locations 35-59. At each location seismic travel times are measured in drill holes, normally at 2.5-m intervals to a depth of 30 m. Geologic logs are determined from drill cuttings, undisturbed (cored) samples, and penetrometer samples. The data provide a detailed comparison of geologic and seismic characteristics and provide parameters for estimating strong earthquake ground motions quantitatively at each of the sites. A major emphasis of this program is to obtain a detailed comparison of geologic and seismic data on a regional scale for use in seismic zonation. There is a variety of geologic and seismic data available in the San Francisco Bay Region for use 1n developing the general zoning techniques which can then be applied to other areas. Shear wave velocities 1n near-surface geologic materials are of especial interest for engineering seismology and seismic zonation studies, yet in general, they are difficult to measure because of contamination by compressional waves. A comparison of various in-situ techniques by Warrick (1974) establishes the reliability of the method utilizing a "horizontal traction" source for sites underlain by bay mud and alluvium. Gibbs, and others (1975a) present data from 12 holes and establishes the reliability of the method for sites underlain by a variety of different rock units and suggest extending the measurements to a large number of sites. Data collected from the first 12 holes also provide an opportunity for developing a routine and efficient procedure for collection and reduction of the data. Gibbs and others (1975b) report preliminary comparisons of the data with the amplification data recorded from nuclear explosions, and the intensity data for the 1906 earthquake. These comparisons show that correlations exist between the three data sets. Average shear wave velocity in each geologic unit form the basis for the preliminary correlations, however, some of the geologic units (that is, granite and Franciscan Formation) exhibit a wide range of shear wave velocity. It is apparent that other factors must be considered in these units, perhaps near surface weathering or fracture spacing. Work is continuing in this area.

California↗
USGS1976

Effects of local geological conditions in the San Francisco Bay region on ground motions and the intensities of the 1906 earthquake

Measurements of ground motion generated by nuclear explosions in Nevada have been completed for 99 locations in the San Francisco Bay region, California. The recordings show marked amplitude variations in the frequency band 0.25 to 3.0 Hz that are consistently related to the local geological conditions of the recording site. The average spectral amplifications observed for vertical and horizontal ground motions are, respectively: (1, 1) for granite, (1.5, 1.6) for the Franciscan Formation, (3.0, 2.7) for the Santa Clara Formation, (3.3, 4.4) for alluvium, and (3.7, 11.3) for bay mud. Spectral amplification curves define predominant ground frequencies in the band 0.25 to 3.0 E for bay mud sites and for some alluvial sites. Amplitude spectra computed from recordings of seismic background noise at 50 sites do not generally define predominant ground frequencies. The intensities ascribed to various sites in the San Francisco Bay region for the California earthquake of April 18, 1906, are strongly dependent on distance from the zone of surface faulting and the geological character of the ground. Considering only those sites (approximately one square city block in size) for which there is good evidence for the degree of ascribed intensity, the intensities for 917 sites on Franciscan rocks generally decrease with the logarithm of distance as Intensity = 2.69 - 1.90 log (Distance in kilometers). (1) For sites on other geological units, intensity increments, derived from this empirical relation, correlate strongly with the Average Horizontal Spectral Amplifications (AHSA) according to the empirical relation Intensity Increment = 0.27 + 2.70 log (AHSA). (2) Average intensity increments predicted for the various geological units are −0.3 for granite, 0.2 for the Franciscan Formation, 0.6 for the Great Valley sequence, 0.8 for the Santa Clara Formation, 1.3 for alluvium, and 2.4 for bay mud. The maximum intensity map predicted on the basis of these data delineates areas in the San Francisco Bay region of potentially high intensity for large earthquakes on either the San Andreas fault or the Hayward fault. The map provides a crude form of seismic zonation for the region and may be useful for certain general types of land-use zonation.

California↗
USGS1976

In-situ measurements of seismic velocities in the San Francisco Bay region...Part II

Seismic wave velocities (compressional and shear) are important parameters for determining the seismic response characteristics of various geologic units when subjected to strong earthquake ground shaking. Seismic velocities of various units often show a strong correlation with the amounts of damage following large earthquakes and have been used as a basis for certain types of seismic zonation studies. Currently a program is in progress to measure seismic velocities in the San Francisco Bay region at an estimated 150 sites. At each site seismic travel times are measured in drill holes, normally at 2.5-m intervals to a depth of 30 m. Geologic logs are determined from drill hole cuttings, undisturbed samples, and penetrometer samples. The data provide a detailed comparison of geologic and seismic characteristics and provide parameters for estimating strong earthquake ground motions quantitatively at each of the site. A major emphasis of this program is to obtain a detailed comparison of geologic and seismic data on a regional scale for use in seismic zonation. The broad data base available in the San Francisco Bay region suggests using the area as a pilot area for the development of general techniques applicable to other areas.

California↗
USGS1975

Maps showing maximum earthquake intensity predicted in the southern San Francisco Bay region, California, for large earthquakes on the San Andreas and Hayward Faults

This map shows maximum earthquake intensity predicted at specific sites using the empirical relations derived from the reliable 1906 intensity data (figs. 3 and 4; see text). The numbers 4-0 correspond to letters A-E, respectively, of the San Francisco intensity scale. The predicted intensity value shown for each site is the maximum of those predicted for the site assuming that a large earthquake were to occur on either the San Andreas or the Hayward fault. The map suggests that an earthquake on either fault could cause as much damage at some sites distant from the faults as at sites in the immediate zone of potential surface faulting.

California↗
USGS1975

Prediction of maximum earthquake intensities for the San Francisco Bay region

The intensity data for the California earthquake of April 18, 1906, are strongly dependent on distance from the zone of surface faulting and the geological character of the ground. Considering only those sites (approximately one square city block in size) for which there is good evidence for the degree of ascribed intensity, the empirical relation derived between 1906 intensities and distance perpendicular to the fault for 917 sites underlain by rocks of the Franciscan Formation is: Intensity = 2.69 - 1.90 log (Distance) (km). For sites on other geologic units intensity increments, derived with respect to this empirical relation, correlate strongly with the Average Horizontal Spectral Amplifications (AHSA) determined from 99 three-component recordings of ground motion generated by nuclear explosions in Nevada. The resulting empirical relation is: Intensity Increment = 0.27 +2.70 log (AHSA), and average intensity increments for the various geologic units are -0.29 for granite, 0.19 for Franciscan Formation, 0.64 for the Great Valley Sequence, 0.82 for Santa Clara Formation, 1.34 for alluvium, 2.43 for bay mud. The maximum intensity map predicted from these empirical relations delineates areas in the San Francisco Bay region of potentially high intensity from future earthquakes on either the San Andreas fault or the Hazard fault.

Open-File Report↗
USGS1974

Effects of local geology on ground motion in the San Francisco Bay region, California: A continued study

Measurements of ground motion generated by nuclear explosions in Nevada have been completed for 99 locations in the San Francisco Bay region, California. The seismograms, Fourier amplitude spectra, spectral amplification curves for the signal, and the Fourier amplitude spectra of the seismic noise are presented for 60 locations. Analog amplifications, based on the maximum signal amplitude, are computed for an additional 39 locations. The recordings of the nuclear explosions show marked amplitude variations which are consistently related to the local geologic conditions of the recording site. The average spectral amplifications observed for vertical and horizontal ground motions are, respectively: (1, 1) for granite, (1.5, 1.6) for the Franciscan Formation, (2.3, 2.3), for other pre-Tertiary and Tertiary rocks, (3.0, 2.7) for the Santa Clara Formation, (3.3, 4.4) for older bay sediments, and (3.7, 11.3) for younger bay mud. Spectral amplification curves define predominant ground frequencies for younger bay mud sites and for some older bay sediment sites. The predominant frequencies for most sites were not clearly defined by the amplitude spectra computed from the seismic background noise. The intensities ascribed to various sites in the San Francisco Bay region for the California earthquake of April 18, 1906, are strongly dependent on distance from the zone of surface faulting and the geological character of the ground. Considering only those sites (approximately one square city block in size) for which there is good evidence for the degree of ascribed intensity, the intensities for 917 sites on Franciscan rocks generally decrease with the logarithm of distance as Intensity = 2.69 - 1.90 log (Distance Km). For sites on other geologic units, intensity increments, derived from this empirical rela.tion, correlate strongly with the Average Horizontal Spectral Amplifications (MISA) according to the empirical relation Intensity Increment= 0.27 + 2.70 log(AHSA). Average intensity increments predicted for various geologic units are -0.3 for granite, 0.2 for Franciscan Formation, 0.6 for other pre-Tertiary, Tertiary bedrock, 0.8 for Santa Clara Formation, 1 .3 for older bay sediments, 2.4 for younger bay mud. These empirical relations, together with detailed geologic maps, delineate areas in the San Francisco Bay region of potentially high intensity from future earthquakes on either the San Andreas fault or the Hayward fault.

California↗