USGS Science⌕ Search

Geology topics

I.A. Pecher

Publications and source records attributed to I.A. Pecher.

9 recordsLinked to original sources
USGS2007

Methane gas hydrate effect on sediment acoustic and strength properties

To improve our understanding of the interaction of methane gas hydrate with host sediment, we studied: (1) the effects of gas hydrate and ice on acoustic velocity in different sediment types, (2) effect of different hydrate formation mechanisms on measured acoustic properties (3) dependence of shear strength on pore space contents, and (4) pore pressure effects during undrained shear. A wide range in acoustic p-wave velocities (V p ) were measured in coarse-grained sediment for different pore space occupants. V p ranged from less than 1 km/s for gas-charged sediment to 1.77–1.94 km/s for water-saturated sediment, 2.91–4.00 km/s for sediment with varying degrees of hydrate saturation, and 3.88–4.33 km/s for frozen sediment. V p measured in fine-grained sediment containing gas hydrate was substantially lower (1.97 km/s). Acoustic models based on measured V p indicate that hydrate which formed in high gas flux environments can cement coarse-grained sediment, whereas hydrate formed from methane dissolved in the pore fluid may not. The presence of gas hydrate and other solid pore-filling material, such as ice, increased the sediment shear strength. The magnitude of that increase is related to the amount of hydrate in the pore space and cementation characteristics between the hydrate and sediment grains. We have found, that for consolidation stresses associated with the upper several hundred meters of sub-bottom depth, pore pressures decreased during shear in coarse-grained sediment containing gas hydrate, whereas pore pressure in fine-grained sediment typically increased during shear. The presence of free gas in pore spaces damped pore pressure response during shear and reduced the strengthening effect of gas hydrate in sands.

Journal of Petroleum Science and Engineering↗
USGS2004

Physical properties and rock physics models of sediment containing natural and laboratory-formed methane gas hydrate

This paper presents results of shear strength and acoustic velocity (p-wave) measurements performed on: (1) samples containing natural gas hydrate from the Mallik 2L-38 well, Mackenzie Delta, Northwest Territories; (2) reconstituted Ottawa sand samples containing methane gas hydrate formed in the laboratory; and (3) ice-bearing sands. These measurements show that hydrate increases shear strength and p-wave velocity in natural and reconstituted samples. The proportion of this increase depends on (1) the amount and distribution of hydrate present, (2) differences, in sediment properties, and (3) differences in test conditions. Stress-strain curves from the Mallik samples suggest that natural gas hydrate does not cement sediment grains. However, stress-strain curves from the Ottawa sand (containing laboratory-formed gas hydrate) do imply cementation is present. Acoustically, rock physics modeling shows that gas hydrate does not cement grains of natural Mackenzie Delta sediment. Natural gas hydrates are best modeled as part of the sediment frame. This finding is in contrast with direct observations and results of Ottawa sand containing laboratory-formed hydrate, which was found to cement grains (Waite et al. 2004). It therefore appears that the microscopic distribution of gas hydrates in sediment, and hence the effect of gas hydrate on sediment physical properties, differs between natural deposits and laboratory-formed samples. This difference may possibly be caused by the location of water molecules that are available to form hydrate. Models that use laboratory-derived properties to predict behavior of natural gas hydrate must account for these differences.

American Mineralogist↗
USGS2003

Seismic anisotropy in gas-hydrate- and gas-bearing sediments on the Blake Ridge, from a walkaway vertical seismic profile

We present results from an analysis of anisotropy in marine sediments using walkaway vertical seismic profiles from the Blake Ridge, offshore South Carolina. We encountered transverse isotropy (TI) with a vertical symmetry axis in a gas-hydrate-bearing unit of clay and claystone with Thomsen parameters ?? = 0.05 ?? 0.02 and ?? = 0.04 ?? 0.06. TI increased to ?? = 0.16 ?? 0.04 and ?? = 0.19 ?? 0.12 in the underlying gas zone. Rock physics modeling suggests that the observed TI is caused by a partial alignment of clay particles rather than high-velocity gas-hydrate veins. Similarly, the increase of TI in the gas zone is not caused by thin low-velocity gas layers but rather, we speculate, by the sharp contrast between seismic properties of an anisotropic sediment frame and elongated gas-bearing pore voids. Our results underscore the significance of anisotropy for integrating near-vertical and wide-angle seismic data.

Geophysical Research Letters↗
USGS2000

Trapping and migration of methane associated with the gas hydrate stability zone at the Blake Ridge Diapir: New insights from seismic data

The Blake Ridge Diapir is the southernmost of a line of salt diapirs along the Carolina trough. Diapirs cause faulting of the superjacent sediments, creating pathways for migration of fluids and gas to the seafloor. We analyzed reflection seismic data from the Blake Ridge Diapir, which is located in a region with known abundant gas hydrate occurrence. A striking feature in these data is a significant shallowing of the base of gas hydrate stability (BGHS) over the center of the diapir. The seafloor is warped up by about 100 m above the diapir, from about 2300 m to about 2200 m. The BGHS, as indicated by a bottom simulating reflection (BSR), is about 4.5 s off the flanks of the diapir, rising to about 4.15 s at the center. Above the diapir, a fault system appears to rise vertically from the BGHS to about 0.05 s below the seafloor (40-50 m); it then diverges into several steeply dipping faults that breach the seafloor and cover an area ~700 m in diameter. Other secondary faults diverge from the main fault or emerge directly from the BGHS near the crest of the diapir. Gas and other fluids may migrate upward through the faults. We performed complex trace analysis to compare the reflection strength and instantaneous frequency along individual reflections. A low-frequency anomaly over the center of the diapir indicates high seismic attenuation. This is interpreted to be caused by migration of fluids (probably methane) along fault pathways. The migration of gas (i.e. probably mainly methane) through the gas hydrate stability zone is not yet understood. We speculate that pore fluids in the faults may be too warm and too salty to form gas hydrate, even at depths where gas hydrate is stable away from the diapir. Alternatively, gas hydrates may seal the fault walls such that water supply is too low to transform all the gas into gas hydrates. The shallowing of the BSR may reflect increased heatflow above the diapir either caused by the high thermal conductivity of the underlying salt or by advective heat transport along with fluids. High pore water salinity shifts the gas hydrate stability to lower temperatures and may also play a significant role in BSR shallowing. We, therefore, investigated the possible effect of pore water salinity on shallowing of the BSR. We found that BSR shallowing may theoretically be entirely caused by increased salinity over the diapir, although geologically this would not be reasonable. This observation demonstrates the potential importance of pore water salinity for lateral variations of BSR depths, in particular, above salt structures: (C) 2000 Elsevier Science B.V.

Blake Ridge Diapir↗
USGS1997

Offset-vertical seismic profiling for marine gas hydrate exploration: Is it a suitable technique? First results from ODP Leg 164

Walkaway vertical seismic profiles were acquired during Ocean Drilling Project (ODP) Leg 164 at the Blake Ridge to investigate seismic properties of hydrate-bearing sediments and the zone of free gas beneath them. An evaluation of compressional (P-) wave arrivals Site 994 indicates P-wave anisotrophy in the sediment column. We identified several shear (S-) wave arrivals in the horizontal components of the geophone array in the borehole and in data recorded with an ocean bottom seismometer deployed at the seafloor. S-waves were converted from P-waves at several depth levels in the sediment column. One of the most prominent conversion points appears to be the bottom simulating reflector (BSR). It is likely that other conversion points are located in the zone of low P-wave reflectivity above the BSR. Modeling suggests that a change of the shear modulus is sufficient to cause significant shear conversion without a significant normal-incidence P-wave reflection.

North Carolina, South Carolina↗
USGS1996

Velocity structure of a bottom simulating reflector offshore Peru: Results from full waveform inversion

Much of our knowledge of the worldwide distribution of submarine gas hydrates comes from seismic observations of Bottom Simulating Reflectors (BSRs). Full waveform inversion has proven to be a reliable technique for studying the fine structure of BSRs using the compressional wave velocity. We applied a non-linear full waveform inversion technique to a BSR at a location offshore Peru. We first determined the large-scale features of seismic velocity variations using a statistical inversion technique to maximise coherent energy along travel-time curves. These velocities were used for a starting velocity model for the full waveform inversion, which yielded a detailed velocity/depth model in the vicinity of the BSR. We found that the data are best fit by a model in which the BSR consists of a thin, low-velocity layer. The compressional wave velocity drops from 2.15 km/s down to an average of 1.70 km/s in an 18m thick interval, with a minimum velocity of 1.62 km/s in a 6 m interval. The resulting compressional wave velocity was used to estimate gas content in the sediments. Our results suggest that the low velocity layer is a 6-18 m thick zone containing a few percent of free gas in the pore space. The presence of the BSR coincides with a region of vertical uplift. Therefore, we suggest that gas at this BSR is formed by a dissociation of hydrates at the base of the hydrate stability zone due to uplift and subsequently a decrease in pressure.

Earth and Planetary Science Letters↗