Geology topics

E. L. Harp

Publications and source records attributed to E. L. Harp.

At least 19 recordsLinked to original sources

USGS2011

Landslide inventories: The essential part of seismic landslide hazard analyses

A detailed and accurate landslide inventory is an essential part of seismic landslide hazard analysis. An ideal inventory would cover the entire area affected by an earthquake and include all of the landslides that are possible to detect down to sizes of 1–5 m in length. The landslides must also be located accurately and mapped as polygons depicting their true shapes. Such mapped landslide distributions can then be used to perform seismic landslide hazard analysis and other quantitative analyses. Detailed inventory maps of landslide triggered by earthquakes began in the early 1960s with the use of aerial photography. In recent years, advances in technology have resulted in the accessibility of satellite imagery with sufficiently high resolution to identify and map all but the smallest of landslides triggered by a seismic event. With this ability to view any area of the globe, we can acquire imagery for any earthquake that triggers significant numbers of landslides. However, a common problem of incomplete coverage of the full distributions of landslides has emerged along with the advent of high resolution satellite imagery.

Engineering Geology↗

USGS2010

Evolution of earthquake-triggered landslides in the Kashmir Himalaya, northern Pakistan

The influence of the 08 October 2005 Kashmir earthquake and subsequent snow melt and monsoon rainfall on slope stability was evaluated using repeat photography in the Kashmir Himalaya of northern Pakistan. Sixty-eight landslide-affected locations were selected and photographed in November 2005, May/June 2006, June 2007, and August 2007 to evaluate all potential geomorphic changes. Eighty percent of the locations showed no or very little change, 11% of the locations showed a partial vegetation recovery on the slopes, while 9% showed an increase in the landslide area. All those locations that showed an increase in landsliding were located along rivers and/or roads. The small change in landslide extent is remarkable given that the region experienced one of the heaviest monsoon seasons in the last decade and is counter to earlier predictions of accelerated slope erosion by landsliding in the immediate years following the earthquake. Extensive fissures and ground cracks at many localities, however, still present a potential of future landsliding under wetter conditions. ?? 2009 Elsevier B.V. All rights reserved.

Geomorphology↗

USGS2009

Interpretation of earthquake-induced landslides triggered by the 12 May 2008, M7.9 Wenchuan earthquake in the Beichuan area, Sichuan Province, China using satellite imagery and Google Earth

The 12 May 2008 M7.9 Wenchuan earthquake in the People's Republic of China represented a unique opportunity for the international community to use commonly available GIS (Geographic Information System) tools, like Google Earth (GE), to rapidly evaluate and assess landslide hazards triggered by the destructive earthquake and its aftershocks. In order to map earthquake-triggered landslides, we provide details on the applicability and limitations of publicly available 3-day-post- and pre-earthquake imagery provided by GE from the FORMOSAT-2 (formerly ROCSAT-2; Republic of China Satellite 2). We interpreted landslides on the 8-m-resolution FORMOSAT-2 image by GE; as a result, 257 large landslides were mapped with the highest concentration along the Beichuan fault. An estimated density of 0.3 landslides/km 2 represents a minimum bound on density given the resolution of available imagery; higher resolution data would have identified more landslides. This is a preliminary study, and further study is needed to understand the landslide characteristics in detail. Although it is best to obtain landslide locations and measurements from satellite imagery having high resolution, it was found that GE is an effective and rapid reconnaissance tool. ?? 2009 Springer-Verlag.

Landslides↗

USGS2009

Mapping of hazard from rainfall-triggered landslides in developing countries: Examples from Honduras and Micronesia

Loss of life and property caused by landslides triggered by extreme rainfall events demonstrates the need for landslide-hazard assessment in developing countries where recovery from such events often exceeds the country's resources. Mapping landslide hazards in developing countries where the need for landslide-hazard mitigation is great but the resources are few is a challenging, but not intractable problem. The minimum requirements for constructing a physically based landslide-hazard map from a landslide-triggering storm, using the simple methods we discuss, are: (1) an accurate mapped landslide inventory, (2) a slope map derived from a digital elevation model (DEM) or topographic map, and (3) material strength properties of the slopes involved. Provided that the landslide distribution from a triggering event can be documented and mapped, it is often possible to glean enough topographic and geologic information from existing databases to produce a reliable map that depicts landslide hazards from an extreme event. Most areas of the world have enough topographic information to provide digital elevation models from which to construct slope maps. In the likely event that engineering properties of slope materials are not available, reasonable estimates can be made with detailed field examination by engineering geologists or geotechnical engineers. Resulting landslide hazard maps can be used as tools to guide relocation and redevelopment, or, more likely, temporary relocation efforts during severe storm events such as hurricanes/typhoons to minimize loss of life and property. We illustrate these methods in two case studies of lethal landslides in developing countries: Tegucigalpa, Honduras (during Hurricane Mitch in 1998) and the Chuuk Islands, Micronesia (during Typhoon Chata'an in 2002).

Engineering Geology↗

USGS2008

Ferguson rock slide buries California State Highway near Yosemite National Park

During spring 2006, talus from the toe area of a rock-block slide of about 800,000 m3 buried California State Highway 140, one of the main routes into heavily-visited Yosemite National Park, USA. Closure of the highway for 92 days caused business losses of about 4.8 million USD. The rock slide, composed of slate and phyllite, moved slowly downslope from April to June 2006, creating a fresh head scarp with 9-12 m of displacement. Movement of the main rock slide, a re-activation of an older slide, was triggered by an exceptionally wet spring 2006, following a very wet spring 2005. As of autumn 2006, most of the main slide appeared to be at rest, although rocks occasionally continued to fall from steep, fractured rock masses at the toe area of the slide. Future behavior of the slide is difficult to predict, but possible scenarios range from continued scattered rock fall to complete rapid failure of the entire mass. Although unlikely except under very destabilizing circumstances, a worst-case, rapid failure of the entire rock slide could extend across the Merced River, damming the river and creating a reservoir. As a temporary measure, traffic has been rerouted to the opposite side of the Merced River at about the same elevation as the buried section of Highway 140. A state-of-the-art monitoring system has been installed to detect movement in the steep talus slope, movement of the main slide mass, local strong ground motion from regional earthquakes, and sudden changes in stream levels, possibly indicating damming of the river by slide material. ?? 2008 Springer-Verlag.

Landslides↗

USGS2008

Transient deterministic shallow landslide modeling: Requirements for susceptibility and hazard assessments in a GIS framework

Application of transient deterministic shallow landslide models over broad regions for hazard and susceptibility assessments requires information on rainfall, topography and the distribution and properties of hillside materials. We survey techniques for generating the spatial and temporal input data for such models and present an example using a transient deterministic model that combines an analytic solution to assess the pore-pressure response to rainfall infiltration with an infinite-slope stability calculation. Pore-pressures and factors of safety are computed on a cell-by-cell basis and can be displayed or manipulated in a grid-based GIS. Input data are high-resolution (1.8??m) topographic information derived from LiDAR data and simple descriptions of initial pore-pressure distribution and boundary conditions for a study area north of Seattle, Washington. Rainfall information is taken from a previously defined empirical rainfall intensity-duration threshold and material strength and hydraulic properties were measured both in the field and laboratory. Results are tested by comparison with a shallow landslide inventory. Comparison of results with those from static infinite-slope stability analyses assuming fixed water-table heights shows that the spatial prediction of shallow landslide susceptibility is improved using the transient analyses; moreover, results can be depicted in terms of the rainfall intensity and duration known to trigger shallow landslides in the study area.

Engineering Geology↗

USGS2008

Landslides triggered by the 8 October 2005 Kashmir earthquake

The 8 October 2005 Kashmir earthquake triggered several thousand landslides. These were mainly rock falls and debris falls, although translational rock and debris slides also occurred. In addition, a sturzstrom (debris avalanche) comprising ??? 80??million m3 buried four villages and blocked streams to create two lakes. Although landsliding occurred throughout the region, covering an area of > 7500??km2, the failures were highly concentrated, associated with six geomorphic-geologic-anthropogenic settings, including natural failures in (1) highly fractured carbonate rocks comprising the lowest beds in the hanging wall of the likely earthquake fault; (2) Tertiary siliciclastic rocks along antecedent drainages that traverse the Hazara-Kashmir Syntaxis; (3) steep (> 50??) slopes comprising Precambrian and Lower Paleozoic rocks; (4) very steep (?? 50??) lower slopes of fluvially undercut Quaternary valley fills; and (5) ridges and spur crests. The sixth setting was associated with road construction. Extensive fissuring in many of the valley slopes together with the freshly mobilized landslide debris constitutes a potential hazard in the coming snowmelt and monsoon seasons. This study supports the view that earthquake-triggered landslides are highly concentrated in specific zones associated with the lithology, structure, geomorphology, topography, and human presence. ?? 2007 Elsevier B.V. All rights reserved.

Geomorphology↗

USGS2008

Rapid Assessment of earthquake-induced landsliding

The Pacific Northwest in the United States including Seattle, Washington, experienced unusually heavy rainfall in the winters of 1995/1996 and 1996/1997, which caused numerous landslides. Following these two winters, the City of Seattle resolved to reduce future landslide losses within its jurisdiction. By coincidence, in 1997 the U.S. Geological Survey (USGS) began a five-year project designed to increase scientific understanding of all the natural hazards facing the Seattle area, including landslides. This article documents the convergence of the efforts of the City of Seattle, the State of Washington, and the USGS to understand the landslide hazards facing the Seattle area and to implement hazard reduction and mitigation of damage from landslides. Specifically, this article identifies how and where USGS information on landslide hazards fit in with efforts already undertaken by the City. This combined effort enabled the City of Seattle to understand its landslide hazards, to formulate public policy, to educate its citizens, and to coordinate the activities of the numerous departments under its jurisdiction with the ultimate goal of lessening the impact of landslides. The City used USGS maps and reports to guide decisions that prioritized funds for siting, maintaining and constructing public facilities in addition to meeting Washington State laws that mandated growth management and environmental review.

Conference Paper↗

USGS2007

Influence of tectonic folding on rockfall susceptibility, American Fork Canyon, Utah, USA

We examine rockfall susceptibility of folded strata in the Sevier fold-thrust belt exposed in American Fork Canyon in north-central Utah. Large-scale geologic mapping, talus production data, rock-mass-quality measurements, and historical rockfall data indicate that rockfall susceptibility is correlated with limb dip and curvature of the folded, cliff-forming Mississippian limestones. On fold limbs, rockfall susceptibility increases as dip increases. This relation is controlled by several factors, including an increase in adverse dip conditions and apertures of discontinuities, and shearing by flexural slip during folding that has reduced the friction angles of discontinuities by smoothing surface asperities. Susceptibility is greater in fold hinge zones than on adjacent limbs primarily because there are greater numbers of discontinuities in hinge zones. We speculate that susceptibility increases in hinge zones as fold curvature becomes tighter.

Natural Hazards and Earth System Sciences↗

USGS2006

Large rock avalanches triggered by the M 7.9 Denali Fault, Alaska, earthquake of 3 November 2002

The moment magnitude (M) 7.9 Denali Fault, Alaska, earthquake of 3 November 2002 triggered thousands of landslides, primarily rock falls and rock slides, that ranged in volume from rock falls of a few cubic meters to rock avalanches having volumes as great as 20 ?? 106 m3. The pattern of landsliding was unusual: the number and concentration of triggered slides was much less than expected for an earthquake of this magnitude, and the landslides were concentrated in a narrow zone about 30-km wide that straddled the fault-rupture zone over its entire 300-km length. Despite the overall sparse landslide concentration, the earthquake triggered several large rock avalanches that clustered along the western third of the rupture zone where acceleration levels and ground-shaking frequencies are thought to have been the highest. Inferences about near-field strong-shaking characteristics drawn from interpretation of the landslide distribution are strikingly consistent with results of recent inversion modeling that indicate that high-frequency energy generation was greatest in the western part of the fault-rupture zone and decreased markedly to the east. ?? 2005 Elsevier B.V. All rights reserved.

Engineering Geology↗

USGS2005

Regional landslide-hazard assessment for Seattle, Washington, USA

Landslides are a widespread, frequent, and costly hazard in Seattle and the Puget Sound area of Washington State, USA. Shallow earth slides triggered by heavy rainfall are the most common type of landslide in the area; many transform into debris flows and cause significant property damage or disrupt transportation. Large rotational and translational slides, though less common, also cause serious property damage. The hundreds of landslides that occurred during the winters of 1995-96 and 1996-97 stimulated renewed interest by Puget Sound communities in identifying landslide-prone areas and taking actions to reduce future landslide losses. Informal partnerships between the U.S. Geological Survey (USGS), the City of Seattle, and private consultants are focusing on the problem of identifying and mapping areas of landslide hazard as well as characterizing temporal aspects of the hazard. We have developed GIS-based methods to map the probability of landslide occurrence as well as empirical rainfall thresholds and physically based methods to forecast times of landslide occurrence. Our methods for mapping landslide hazard zones began with field studies and physically based models to assess relative slope stability, including the effects of material properties, seasonal groundwater levels, and rainfall infiltration. We have analyzed the correlation between historic landslide occurrence and relative slope stability to map the degree of landslide hazard. The City of Seattle is using results of the USGS studies in storm preparedness planning for emergency access and response, planning for development or redevelopment of hillsides, and municipal facility planning and prioritization. Methods we have developed could be applied elsewhere to suit local needs and available data.

Landslides↗

USGS2004

Landslides triggered by the 2002 Denali fault, Alaska, earthquake and the inferred nature of the strong shaking

The 2002 M7.9 Denali fault, Alaska, earthquake triggered thousands of landslides, primarily rock falls and rock slides, that ranged in volume from rock falls of a few cubic meters to rock avalanches having volumes as great as 15 ?? 106 m3. The pattern of landsliding was unusual; the number of slides was less than expected for an earthquake of this magnitude, and the landslides were concentrated in a narrow zone 30-km wide that straddled the fault rupture over its entire 300-km length. The large rock avalanches all clustered along the western third of the rupture zone where acceleration levels and ground-shaking frequencies are thought to have been the highest. Inferences about near-field strong shaking characteristics drawn from the interpretation of the landslide distribution are consistent with results of recent inversion modeling that indicate high-frequency energy generation was greatest in the western part of the fault rupture zone and decreased markedly to the east. ?? 2004, Earthquake Engineering Research Institute.

Earthquake Spectra↗

USGS2003

The 2002 Denali fault earthquake, Alaska: A large magnitude, slip-partitioned event

The MW (moment magnitude) 7.9 Denali fault earthquake on 3 November 2002 was associated with 340 kilometers of surface rupture and was the largest strike-slip earthquake in North America in almost 150 years. It illuminates earthquake mechanics and hazards of large strike-slip faults. It began with thrusting on the previously unrecognized Susitna Glacier fault, continued with right-slip on the Denali fault, then took a right step and continued with right-slip on the Totschunda fault. There is good correlation between geologically observed and geophysically inferred moment release. The earthquake produced unusually strong distal effects in the rupture propagation direction, including triggered seismicity.

Science↗

USGS2003

Landslides and liquefaction triggered by the M 7.9 denali fault earthquake of 3 November 2002

The moment magnitude (M) 7.9 Denali Fault earthquake in Alaska of 3 November 2002 triggered an unusual pattern of landslides and liquefaction effects. The landslides were primarily rock falls and rock slides that ranged in volume from a few cubic meters to the 40 million-cubic-meter rock avalanche that covered much of the McGinnis Glacier. Landslides were concentrated in a narrow zone ???30 km wide that straddled the fault rupture zone over its entire 300 km length. Large rock avalanches all clustered at the western end of the rupture zone where acceleration levels are reported to have been the highest. Liquefaction effects, consisting of sand blows, lateral spreads, and settlement, were widespread within susceptible alluvial deposits extending from Fairbanks eastward several hundred kilometers. The liquefaction effects displayed a pattern of increasing concentration and severity from west to east and extended well beyond the zone of landslides, which is unusual. The contrasting patterns formed by the distributions of landslides and liquefaction effects initially seemed to be inconsistent; however, preliminary analyses of strong-motion records from the earthquake offer a possible explanation for the unusual ground-failure patterns that are related to three subevents that have been discerned from the earthquake records.

GSA Today↗

USGS2000

A method for producing digital probabilistic seismic landslide hazard maps

The 1994 Northridge, California, earthquake is the first earthquake for which we have all of the data sets needed to conduct a rigorous regional analysis of seismic slope instability. These data sets include: (1) a comprehensive inventory of triggered landslides, (2) about 200 strong-motion records of the mainshock, (3) 1:24 000-scale geologic mapping of the region, (4) extensive data on engineering properties of geologic units, and (5) high-resolution digital elevation models of the topography. All of these data sets have been digitized and rasterized at 10 m grid spacing using ARC/INFO GIS software on a UNIX computer. Combining these data sets in a dynamic model based on Newmark's permanent-deformation (sliding-block) analysis yields estimates of coseismic landslide displacement in each grid cell from the Northridge earthquake. The modeled displacements are then compared with the digital inventory of landslides triggered by the Northridge earthquake to construct a probability curve relating predicted displacement to probability of failure. This probability function can be applied to predict and map the spatial variability in failure probability in any ground-shaking conditions of interest. We anticipate that this mapping procedure will be used to construct seismic landslide hazard maps that will assist in emergency preparedness planning and in making rational decisions regarding development and construction in areas susceptible to seismic slope failure. ?? 2000 Elsevier Science B.V. All rights reserved.

Engineering Geology↗

USGS2000

Unusual July 10, 1996, rock fall at Happy Isles, Yosemite National Park, California

Effects of the July 10, 1996, rock fall at Happy Isles in Yosemite National Park, California, were unusual compared to most rock falls. Two main rock masses fell about 14 s apart from a 665-m-high cliff southeast of Glacier Point onto a talus slope above Happy Isles in the eastern part of Yosemite Valley. The two impacts were recorded by seismographs as much as 200 km away. Although the impact area of the rock falls was not particularly large, the falls generated an airblast and an abrasive dense sandy cloud that devastated a larger area downslope of the impact sites toward the Happy Isles Nature Center. Immediately downslope of the impacts, the airblast had velocities exceeding 110 m/s and toppled or snapped about 1000 trees. Even at distances of 0.5 km from impact, wind velocities snapped or toppled large trees, causing one fatality and several serious injuries beyond the Happy Isles Nature Center. A dense sandy cloud trailed the airblast and abraded fallen trunks and trees left standing. The Happy Isles rock fall is one of the few known worldwide to have generated an airblast and abrasive dense sandy cloud. The relatively high velocity of the rock fall at impact, estimated to be 110-120 m/s, influenced the severity and areal extent of the airblast at Happy Isles. Specific geologic and topographic conditions, typical of steep glaciated valleys and mountainous terrain, contributed to the rock-fall release and determined its travel path, resulting in a high velocity at impact that generated the devastating airblast and sandy cloud. The unusual effects of this rock fall emphasize the importance of considering collateral geologic hazards, such as airblasts from rock falls, in hazard assessment and planning development of mountainous areas.

California↗

USGS2000

Map showing recent and historic landslide activity on coastal bluffs of Puget Sound between Shilshole Bay and Everett, Washington

Many landslides occurred on the coastal bluffs between Seattle and Everett, Washington during the winters of 1996 and 1997. Shallow earth slides and debris flows were the most common, but a few deep-seated rotational earth slides also occurred. The landslides caused significant property damage and interfered with rail traffic; future landslides in the area pose significant hazards to property and public safety. Field observations indicate that ground-water seepage, runoff concentration, and dumping at the tops of the bluffs all contributed to instability of the bluffs. Most landslides in the study area occurred in colluvium, residuum, and landslide deposits derived from the Vashon Drift, particularly the advance outwash. In the northern part of the area, colluvium derived from the Pleistocene Whidbey Formation was also involved in shallow landslides. Comparison of recent activity with historic records in the southern part of the map area indicates that landslides tend to occur in many of the same areas as previous landslides.

Washington↗

USGS1998

Real-time monitoring of bluff stability at Woodway, Washington, USA

On January 15, 1997, a landslide of approximately 100,000-m3 from a coastal bluff swept five cars of a freight train into Puget Sound at Woodway, Washington, USA, 25 km north of downtown Seattle. The landslide resulted from failure of a sequence of dense sands and hard silts of glacial and non-glacial origin, including the Lawton Clay, a hard, jointed clayey silt that rarely fails in natural slopes. Joints controlled ground-water seepage through the silt and break-up of the landslide mass. During September of 1997, the US Geological Survey began measuring rainfall, ground-water pressures, and slope movement at the bluff where the landslide occurred. Data are collected every 15 minutes and updated hourly on the World-Wide-Web. Pore pressures observed from September 1997 to February 1998 generally were low and pressures near the bluff face, in the upper few meters of the hard clayey silt, increased gradually.

Conference Paper↗