USGS Science⌕ Search

Geology topics

E. Cranswick

Publications and source records attributed to E. Cranswick.

15 recordsLinked to original sources
USGS2002

Site effects in Avcilar, West of Istanbul, Turkey, from strong- and weak-motion data

Approximately 1000 people were killed in the collapse of buildings in Istanbul, Turkey, during the 17 August 1999 I??zmit earthquake, whose epicenter was roughly 90 km east of the city. Most of the fatalities and damage occurred in the suburb of Avcilar that is 20 km further west of the epicenter than the city proper. To investigate this pattern of damage, the U.S. Geological Survey, in cooperation with the Kandilli Observatory and Earthquake Research Institute (KOERI), deployed portable digital seismographs at seven free-field sites in western Istanbul, to record aftershocks during the period from 24 August to 2 September. The primary objective of this deployment was to study the site effects by comparing the aftershock ground motions recorded at sites inside and outside the damaged area, and to correlate site effects with the distribution of the damaged buildings. In addition to using weak-motion data, mainshock and aftershock acceleration records from the KOERI permanent strong-motion array were also used in estimating the site effects. Site effects were estimated using S waves from both types of records. For the weak-motion data set, 22 events were selected according to the criteria of signal-to-noise ratio (S/N ratio) and the number of stations recording the same event. The magnitudes of these events ranged from 3.0 to 5.2. The acceleration data set consisted of 12 events with magnitudes ranging from 4.3 to 5.8 and included two mainshock events. Results show that the amplifying frequency band is, in general, less than 4 Hz, and the physical properties of the geologic materials are capable of amplifying the motions by a factor of 5-10. In this frequency band, there is a good agreement among the spectral ratios obtained from the two mainshocks and their aftershocks. The damage pattern for the 17 August I??zmit earthquake is determined by several factors. However, our study suggests that the site effects in Avcilar played an important role in contributing to the damage.

Bulletin of the Seismological Society of America↗
USGS2001

Observations of basin ground motions from a dense seismic array in San Jose, California

We installed a dense array of 41 digital seismographs in San Jose, California, to evaluate in detail the effects of a deep sedimentary basin and shallow sedimentary deposits on earthquake ground motions. This urban array is located near the eastern edge of the Santa Clara Valley and spans the Evergreen sedimentary basin identified by gravity data. Average station spacing is 1 km, with three stations initially spaced 110 m apart. Despite the high-noise urban environment, the stations of the array successfully triggered on and recorded small local earthquakes (M 2.5-2.8 at 10-25 km distance) and larger regional events such as the M 5.0 Bolinas earthquake (90 km distance), M 4.6-5.6 earthquakes near Mammoth Lakes (270 km distance), M 4.9-5.6 events in western Nevada (420 km distance) and the M 7.1 Hector Mine earthquake (590 km distance). Maps of spectral ratios across the array show that the highest amplitudes in all frequency bands studied (0.125-8 Hz) are generally observed at stations farther from the eastern edge of the Santa Clara Valley. Larger spectral amplitudes are often observed above the western edge of the Evergreen Basin. Snapshots of the recorded wavefield crossing the array for regional events to the east reveal that large, low-frequency (0.125-0.5 Hz) arrivals after the S-wave travel from south to north across the array. A moving-window, cross-correlation analysis finds that these later arrivals are surface waves traveling from the south. The timing and propagation direction of these arrivals indicates that they were likely produced by scattering of incident S waves at the border of the Santa Clara Valley to the south of the array. It is remarkable that the largest low-frequency phases at many of the valley sites for regional events to the east are basin surface waves coming from a direction about 70 degrees different from that of the epicenters. Basin surface waves emanating from the eastern edge of the valley are also identified by the cross-correlation analysis.

Bulletin of the Seismological Society of America↗
USGS2000

Correlation of 1- to 10-Hz earthquake resonances with surface measurements of S-wave reflections and refractions in the upper 50 m

Resonances observed in earthquake seismograms recorded in Seattle, Washington, the central United States and Sherman Oaks, California, are correlated with each site's respective near-surface seismic velocity profile and reflectivity determined from shallow seismic-reflection/refraction surveys. In all of these cases the resonance accounts for the highest amplitude shaking at the site above 1 Hz. These results show that imaging near-surface reflections from the ground surface can locate impedance structures that are important contributors to earthquake ground shaking. A high-amplitude S-wave reflection, recorded 250-m northeast and 300-m east of the Seattle Kingdome earthquake-recording station, with a two-way travel time of about 0.23 to 0.27 sec (about 18- to 22-m depth) marks the boundary between overlying alluvium (VS < 180 m/sec) and a higher velocity material (VS about 400 m/sec). This reflector probably causes a strong 2-Hz resonance that is observed in the earthquake data for the site near the Kingdome. In the central United States, S-wave reflections from a high-impedance boundary (an S-wave velocity increase from about 200 m/sec to 2000 m/sec) at about 40-m depth corresponds to a strong fundamental resonance at about 1.5 Hz. In Sherman Oaks, strong resonances at about 1.0 and 4 Hz are consistently observed on earthquake seismograms. A strong S-wave reflector at about 40-m depth may cause the 1.0 Hz resonance. The 4.0-Hz resonance is possibly explained by constructive interference between the first overtone of the 1.0-Hz resonance and a 3.25- to 3.9-Hz resonance calculated from an areally consistent impedance boundary at about 10-m depth as determined by S-wave refraction data.

Bulletin of the Seismological Society of America↗
USGS1999

Site response for Seattle and source parameters of earthquakes in the Puget Sound Region

We analyzed seismograms from 21 earthquakes ( M L 2.0-4.9) recorded by digital seismographs we deployed in urban Seattle to determine site response and earthquake stress drops. The seismometers were situated on a wide variety of geologic units, including artificial fill (e.g., Kingdome, Harbor Island), Pleistocene age soils (glacial till and outwash deposits of Seattle's hills), modified land (downtown Seattle, Space Needle), and Tertiary sedimentary rock. Two mainshock-aftershock sequences were recorded: the June 1997 Bremerton sequence (mainshock M L 4.9) and the February 1997 South Seattle sequence (mainshock M L 3.5), along with other events in the Puget Sound region. We developed a new inversion procedure to estimate site response, source corner frequencies, and seismic moments from the S -wave spectra. This inversion uses corner frequencies determined from spectral ratios of mainshock-aftershock pairs as constraints. The site responses found from the inversion are not relative to the rock site but are relative to an idealized site with a flat frequency response. The response of the rock site is also found from the inversion. The inversion results show high response for the sites on artificial fill, more moderate amplification for most sites on stiff Pleistocene soils or modified land, and low response for the rock site. Some sites display resonances, such as a strong 2-Hz resonance at our site near the Kingdome, which is caused by the surficial layers of fill and younger alluvium. The sites in West Seattle exhibit high amplification, even though they are on relatively stiff soils of glacial outwash. This may be partly caused by basin surface waves produced by conversion of incident S waves. This high response in West Seattle is consistent with damage reports from the 1949 ( m b 7.1) and 1965 ( m b 6.5) earthquakes. Stress-drop estimates for the events we recorded were generally low, between 0.4 and 25 bars, although some of the events may have had higher stress drops that could not be resolved because of the limited passband. We calculated a stress drop of 24 bars for the Bremerton mainshock and 10 bars for the South Seattle mainshock.

Washington↗
USGS1997

Variability of site response in the Los Angeles urban area

This article addresses the variability of site response in the Los Angeles area and possible structural causes for the observations. Aftershock records from 231 sites in the San Fernando and Los Angeles basins and the surrounding mountains are used in this study. Spectral ratios, taken with respect to a low-amplitude reference site, are used to document the variation in site amplification in the frequency range 2 to 6 Hz, both spatially and with backazimuth to the source. At higher frequencies (6 to 10 Hz), spectral ratios are shown to have greater spatial variability. Interstation spectral ratios are used to measure the standard deviation among source as a function of station separation. An increase in the variation in ground motion is shown to take place at a station separation of 1 km. Relative site-response estimates between nearby stations are used to demonstrate that preferred directions of motion can exist even in areas with no surface topographic effects.

California↗
USGS1996

Urban seismology - Northridge aftershocks recorded by multi-scale arrays of portable digital seismographs

We deployed portable digital seismographs in the San Fernando Valley (SFV), the Los Angeles basin (LAB), and surrounding hills to record aftershocks of the 17 January 1994 Northridge California earthquake. The purpose of the deployment was to investigate factors relevant to seismic zonation in urban areas, such as site amplification, sedimentary basin effects, and the variability of ground motion over short baselines. We placed seismographs at 47 sites (not all concurrently) and recorded about 290 earthquakes with magnitudes up to 5.1 at five stations or more. We deployed widely spaced stations for profiles across the San Fernando Valley, as well as five dense arrays (apertures of 200 to 500 m) in areas of high damage, such as the collapsed Interstate 10 overpass, Sherman Oaks, and the collapsed parking garage at CalState Northridge. Aftershock data analysis indicates a correlation of site amplification with mainshock damage. We found several cases where the site amplification depended on the azimuth of the aftershock, possibly indicating focusing from basin structures. For the parking garage array, we found large ground-motion variabilities (a factor of 2) over 200-m distances for sites on the same mapped soil unit. Array analysis of the aftershock seismograms demonstrates that sizable arrivals after the direct S waves consist of surface waves traveling from the same azimuth as that of the epicenter. These surface waves increase the duration of motions and can have frequencies as high as about 4 Hz. For the events studied here, we do not observe large arrivals reflected from the southern edge of the San Fernando Valley.

California↗
USGS1989

Effect of site conditions on ground motion and damage

Results of seismologic studies conducted by the U.S. reconnaissance team in conjunction with Soviet colleagues following the tragic earthquakes of December 7, 1988, suggest that site conditions may have been a major factor in contributing to increased damage levels in Leninakan. As the potential severity of these effects in Leninakan had not been previously identified, this chapter presents results intended to provide a preliminary quantification of these effects on both damage and levels of ground motion observed in Leninakan. The article describes the damage distribution geologic setting, ground motion amplification in Leninakan, including analog amplifications and spectral amplifications. Preliminary model estimates for site response are presented. It is concluded that ground motion amplification in the 0.5-2.5-second period range was a major contributing factor to increased damage in Leninakan as compared with Kirovakan. Leninakan is located on thick water saturated alluvial deposits.

Shirak↗
USGS1988

The information content of high-frequency seismograms and the near-surface geologic structure of "hard rock" recording sites

Due to hardware developments in the last decade, the high-frequency end of the frequency band of seismic waves analyzed for source mechanisms has been extended into the audio-frequency range (>20 Hz). In principle, the short wavelengths corresponding to these frequencies can provide information about the details of seismic sources, but in fact, much of the "signal" is the site response of the nearsurface. Several examples of waveform data recorded at "hard rock" sites, which are generally assumed to have a "flat" transfer function, are presented to demonstrate the severe signal distortions, including fmax, produced by near-surface structures. Analysis of the geology of a number of sites indicates that the overall attenuation of high-frequency (>1 Hz) seismic waves is controlled by the whole-path-Q between source and receiver but the presence of distinct fmax site resonance peaks is controlled by the nature of the surface layer and the underlying near-surface structure. Models of vertical decoupling of the surface and nearsurface and horizontal decoupling of adjacent sites on hard rock outcrops are proposed and their behaviour is compared to the observations of hard rock site response. The upper bound to the frequency band of the seismic waves that contain significant source information which can be deconvolved from a site response or an array response is discussed in terms of fmax and the correlation of waveform distortion with the outcrop-scale geologic structure of hard rock sites. It is concluded that although the velocity structures of hard rock sites, unlike those of alluvium sites, allow some audio-frequency seismic energy to propagate to the surface, the resulting signals are a highly distorted, limited subset of the source spectra. ?? 1988 Birkha??user Verlag.

Pure and Applied Geophysics PAGEOPH↗
USGS1988

The 1987 Whittier Narrows earthquake in the Los Angeles metropolitan area, California

The Whittier Narrows earthquake sequence (local magnitude, M L = 5.9), which caused over 358-million dollars damage, indicates that assessments of earthquake hazards in the Los Angeles metropolitan area may be underestimated. The sequence ruptured a previously unidentified thrust fault that may be part of a large system of thrust faults that extends across the entire east-west length of the northern margin of the Los Angeles basin. Peak horizontal accelerations from the main shock, which were measured at ground level and in structures, were as high as 0.6 g (where g is the acceleration of gravity at sea level) within 50 kilometers of the epicenter. The distribution of the modified Mercalli intensity VII reflects a broad north-south elongated zone of damage that is approximately centered on the main shock epicenter.

California↗
USGS1988

Vertical seismic profiling of Oroville microearthquakes: Velocity spectra and particle motion as a function of depth

Direct evidence of site distortion of P - and S -wave microearthquake source spectra at Oroville, California, is presented. The data were gathered by placing vertical and three-component seismometers at 90 m intervals in a 500 m borehole through the Cleveland Hill normal fault, on which the 1975, M L = 5.7 Oroville earthquake took place. High-pressure, hydraulic locking mechanisms were used to firmly lock the seismometer packages against the borehole wall. Digital, event-triggering GEOS recorders were used to receive the data. Some 30 seismic events, including 12 microearthquakes, were recorded during the 4 months the seismometers were deployed. By comparing the velocity spectra of microearthquake waves at the different depths, it can be seen that scattering and attenuation in the shallow crust around the borehole dominantly affect high-frequency S waves. Above 15 Hz, the value of the apparent S -wave quality factor, Q as , for the upper 500 m of crust at this site is 9. One feature of this low Q as is a gross difference between S -wave “corner” frequencies observed at ground level and 500 m downhole. For example, the uphole and downhole S -wave corner frequencies for the M coda = 0.4 microearthquake of Julian Day 259 differ by a factor of 2 or more. Low quality factors and depth-dependent corner frequencies were also observed for P waves, but these data are less definitive due to lower signal-to-noise ratios. Based on their three-component particle motions and polarizations, the direct S waves of the microearthquakes appear to be composed of two phases, which have similar amplitudes but different apparent velocities. It is possible that the velocity differences are a result of anisotropy in the underlying rock.

California↗