USGS Science⌕ Search

Geology topics

Diane L. Minasian

Publications and source records attributed to Diane L. Minasian.

11 recordsLinked to original sources
USGS2015

Earthquake rupture process recreated from a natural fault surface

What exactly happens on the rupture surface as an earthquake nucleates, spreads, and stops? We cannot observe this directly, and models depend on assumptions about physical conditions and geometry at depth. We thus measure a natural fault surface and use its 3D coordinates to construct a replica at 0.1 m resolution to obviate geometry uncertainty. We can recreate stick-slip behavior on the resulting finite element model that depends solely on observed fault geometry. We clamp the fault together and apply steady state tectonic stress until seismic slip initiates and terminates. Our recreated M~1 earthquake initiates at contact points where there are steep surface gradients because infinitesimal lateral displacements reduce clamping stress most efficiently there. Unclamping enables accelerating slip to spread across the surface, but the fault soon jams up because its uneven, anisotropic shape begins to juxtapose new high-relief sticking points. These contacts would ultimately need to be sheared off or strongly deformed before another similar earthquake could occur. Our model shows that an important role is played by fault-wall geometry, though we do not include effects of varying fluid pressure or exotic rheologies on the fault surfaces. We extrapolate our results to large fault systems using observed self-similarity properties, and suggest that larger ruptures might begin and end in a similar way, though the scale of geometrical variation in fault shape that can arrest a rupture necessarily scales with magnitude. In other words, fault segmentation may be a magnitude dependent phenomenon and could vary with each subsequent rupture.

Journal of Geophysical Research B: Solid Earth↗
USGS2015

Shear-wave velocity and site-amplification factors for 50 Australian sites determined by the spectral analysis of surface waves method

One-dimensional shear-wave velocity ( V S ) profiles are presented at 50 strong motion sites in New South Wales and Victoria, Australia. The V S profiles are estimated with the spectral analysis of surface waves (SASW) method. The SASW method is a noninvasive method that indirectly estimates the V S at depth from variations in the Rayleigh wave phase velocity at the surface.

Open-File Report↗
USGS2012

Topographic change detection at select archeological sites in Grand Canyon National Park, Arizona, 2007-2010

Human occupation in Grand Canyon, Arizona, dates from at least 11,000 years before present to the modern era. For most of this period, the only evidence of human occupation in this iconic landscape is provided by archeological sites. Because of the dynamic nature of this environment, many archeological sites are subject to relatively rapid topographic change. Quantifying the extent, magnitude, and cause of such change is important for monitoring and managing these archeological sites. Such quantification is necessary to help inform the continuing debate on whether and how controlled releases from Glen Canyon Dam, located immediately upstream of Grand Canyon National Park, are affecting site erosion rates, artifact transport, and archeological resource preservation along the Colorado River in Grand Canyon. Although long-term topographic change resulting from a variety of natural processes is inherent in the Grand Canyon region, continued erosion of archeological sites threatens both the archeological resources and our future ability to study evidence of past cultural habitation. Thus, this subject is of considerable interest to National Park Service managers and other stakeholders in the Glen Canyon Dam Adaptive Management Program. Understanding the causes and effects of archeological site erosion requires a knowledge of several factors, including the location, timing, and magnitude of the changes occurring in relation to archeological resources, the rates of change, and the relative contribution of potential causes. These potential causes include sediment depletion associated with managed flows from Glen Canyon Dam, site-specific weather and overland flow patterns, visitor impacts, and long-term regional climate change. To obtain this information, highly accurate, spatially specific data are needed from sites undergoing change. Using terrestrial lidar techniques, and building upon three previous surveys of archeological sites performed in 2006 and 2007, we collected two new datasets in April and September 2010 and processed and improved upon existing methods to generate high-accuracy (3 to 5 cm vertical change threshold) topographic change-detection maps for 10 survey areas encompassing 9 archeological sites along the Colorado River corridor. We also used terrestrial lidar techniques to investigate several other metrics for studying archeological site stability, including monitoring cultural structures and artifacts and remotely measuring cryptobiotic soil crust areas. Our topographic change results indicate that 9 of 10 survey areas showed signs of either erosion, deposition, or both during the 2007–2010 time interval and that these changes can be linked to a variety of geomorphic processes, primarily overland flow gullying and aeolian sand transport. In several cases, large (>50 cm) vertical change occurred, and in one case, more than 100 m 3 of sediment was eroded. Further, for all sites monitored throughout the river corridor during this time period, the overall signal was related to erosion rather than deposition. These results highlight the potential for rapid archeological site change in Grand Canyon. Whereas the topographic change results presented herein provide the highest level of change detection yet performed on entire archeological sites in Grand Canyon, additional work in combining these results with site-specific weather, hydrology, and geomorphology data is needed to provide a more thorough understanding of the causes of the documented topographic changes. Linking lidar-derived measurements of topographic changes with these other data sources should provide land managers with a scientific basis for making management decisions regarding archeological resources in Grand Canyon National Park and assist in answering open questions regarding the influence that sediment-depleted flows from Glen Canyon Dam have on archeological site stability.

Arizona↗
USGS2009

Terrestrial lidar datasets of New Orleans, Louisiana, levee failures from Hurricane Katrina, August 29, 2005

Hurricane Katrina made landfall with the northern Gulf Coast on August 29, 2005, as one of the strongest hurricanes on record. The storm damage incurred in Louisiana included a number of levee failures that led to the inundation of approximately 85 percent of the metropolitan New Orleans area. Whereas extreme levels of storm damage were expected from such an event, the catastrophic failure of the New Orleans levees prompted a quick mobilization of engineering experts to assess why and how particular levees failed. As part of this mobilization, civil engineering members of the United States Geological Survey (USGS) performed terrestrial lidar topographic surveys at major levee failures in the New Orleans area. The focus of the terrestrial lidar effort was to obtain precise measurements of the ground surface to map soil displacements at each levee site, the nonuniformity of levee height freeboard, depth of erosion where scour occurred, and distress in structures at incipient failure. In total, we investigated eight sites in the New Orleans region, including both earth and concrete floodwall levee breaks. The datasets extend from the 17th Street Canal in the Orleans East Bank area to the intersection of the Gulf Intracoastal Waterway (GIWW) with the Mississippi River Gulf Outlet (MRGO) in the New Orleans East area. The lidar scan data consists of electronic files containing millions of surveyed points. These points characterize the topography of each levee’s postfailure or incipient condition and are available for download through online hyperlinks. The data serve as a permanent archive of the catastrophic damage of Hurricane Katrina on the levee systems of New Orleans. Complete details of the data collection, processing, and georeferencing methodologies are provided in this report to assist in the visualization and analysis of the data by future users.

Louisiana↗
USGS2009

Topographic Change Detection at Select Archeological Sites in Grand Canyon National Park, Arizona, 2006-2007

Topographic change of archeological sites within the Colorado River corridor of Grand Canyon National Park (GCNP) is a subject of interest to National Park Service managers and other stakeholders in the Glen Canyon Dam Adaptive Management Program. Although long-term topographic change resulting from a variety of natural processes is typical in the Grand Canyon region, a continuing debate exists on whether and how controlled releases from Glen Canyon Dam, located immediately upstream of GCNP, are impacting rates of site erosion, artifact transport, and the preservation of archeological resources. Continued erosion of archeological sites threatens both the archeological resources and our future ability to study evidence of past cultural habitation. Understanding the causes and effects of archaeological site erosion requires a knowledge of several factors including the location and magnitude of the changes occurring in relation to archeological resources, the rate of the changes, and the relative contribution of several potential causes, including sediment depletion associated with managed flows from Glen Canyon Dam, site-specific weather patterns, visitor impacts, and long-term climate change. To obtain this information, highly accurate, spatially specific data are needed from sites undergoing change. Using terrestrial lidar data collection techniques and novel TIN- and GRID-based change-detection post-processing methods, we analyzed topographic data for nine archeological sites. The data were collected using three separate data collection efforts spanning 16 months (May 2006 to September 2007). Our results documented positive evidence of erosion, deposition, or both at six of the nine sites investigated during this time interval. In addition, we observed possible signs of change at two of the other sites. Erosion was concentrated in established gully drainages and averaged 12 cm to 17 cm in depth with maximum depths of 50 cm. Deposition was concentrated at specific locations outside of drainages but generally was spread over larger areas (tens to hundreds of square meters). Maximum depths of deposition averaged 12 cm to 15 cm and reached as much as 35 cm. Overall, we found that the spatial distribution and magnitudes of surface change are specific to each site and that a thorough understanding of the geomorphology, weather, and sand supply is requisite for a complete understanding of the data. Additional work in combining these results with site-specific weather, hydrology, and geomorphology data will assist in the development of working models for determining the causes of the documented topographic changes.

Scientific Investigations Report↗
USGS2001

The STRATAFORM Project: U.S. Geological Survey geotechnical studies

This report presents physical property logs of core samples from an offshore area near Eureka, CA. The cores were obtained as part of the STRATAFORM Program (Nittrouer and Kravitz, 1995, 1996), a study investigating how present sedimentation and sediment transport processes influence long-term stratigraphic sequences preserved in the geologic record. The core samples were collected during four separate research cruises to the northern California study area, and data shown in the logs of the cores were collected using a multi-sensor whole core logger. The physical properties collected are useful in identifying stratigraphic units, ground-truthing acoustic imagery and sub-bottom profiles, and in understanding mass movement processes. STRATA FOR mation on M argins was initiated in 1994 by the Office of Naval Research, Marine Geology and Geophysics Department as a coordinated multi-investigator study of continental-margin sediment transport processes and stratigraphy (Nittrouer and Kravitz, 1996). The program is investigating the stratigraphic signature of the shelf and slope parts of the continental margins, and is designed to provide a better understanding of the sedimentary record and a better prediction of strata. Specifically, the goals of the STRATAFORM Program are to (Nittrouer and Kravitz, 1995): - determine the geological relevance of short-term physical processes that erode, transport, and deposit particles and those processes that subsequently rework the seabed over time scales <10 2 years. - improve capabilities for identifying the processes that form the strata observed within the upper ~100 m of the seabed commonly representing 104-106 years of sedimentation. - synthesize this knowledge and bridge the gap between time scales of sedimentary processes and those of sequence stratigraphy. The STRATAFORM Program is divided into studies of the continental shelf and the continental slope; the geotechnical group within the U.S. Geological Survey provides support to both parts of the project.

California↗
USGS1996

Geologic Map of the Cascade Head Area, Northwestern Oregon Coast Range (Neskiwin, Nestucca Bay, Hebo, and Dolph 7.5 minute Quadrangles)

The geology of the Cascade Head area bridges the geology in the Tillamook Highlands to the north (Wells and others, 1994; 1995) with that of the Newport Embayment on the south (Snavely and others, 1976 a,b,c). The four 7.5-minute quadrangles (Neskowin, Nestucca Bay, Hebo, and Dolph) which comprise the Cascade Head area include significant stratigraphic, structural, and igneous data that are essential in unraveling the geology of the northern and central part of the Oregon Coast Range and of the adjacent continental shelf Earlier studies (Snavely and Vokes, 1949) were of a broad reconnaissance nature because of limited access in this rugged, densely forested part of the Siuslaw National Forest. Also, numerous thick sills of late middle Eocene diabase and middle Miocene basalt mask the Eocene stratigraphic relationships. Previous mapping was hampered by a lack of precise biostratigraphic data. However, recent advances in biostratigraphy and radiometric age dating and geochemistry have provided the necessary tools to decipher stratigraphic and structural relationships in the Eocene sedimentary and volcanic rock sequences (W.W. Rau, personal communication, 1978 to 1988; Bukry and Snavely, 1988). Many important stratigraphic and igneous relationships are displayed within the Casacde Head area: (1) turbidite sandstone of the middle Eocene Tyee Formation, which is widespread in the central and southern part of the Oregon Coast Range (Snavely and others, 1964), was not deposited in the western part of the Cascade Head, and is of limited extent north of the map area (Wells and others, 1994); (2) the late middle Eocene Yamhill Formation, which crops out along the west and east flank of the Oregon Coast Range, overlaps older strata and overlies an erosional unconformity on the lower Eocene Siletz River Volcanics (Snavely and others, 1990; 1991); (3) thick sills of late middle Eocene diabase (43 Ma) are widespread in the Cascade Head area and also form much of the eastern flank of the Tillamook Highlands (Wells and others, 1994), but are rare south of the map area; (4) Cascade Head is the northernmost eruptive center of late Eocene alkalic basalts--85 km north of the eruptive center of correlative alkalic flows of the Yachats Basalt in the Newport Embayment (Snavely and Vokes, 1949; Snavely and others, 1990; Barnes and Barnes, 1992; Davis and others, 1995); (5) early Oligocene (33 Ma) sills and dikes of nepheline syenite and camptonite present in the Newport Embayment (Snavely and Wagner, 1961) are not found in the Cascade Head area; (6) extensive middle Oligocene (30 Ma) granophyric gabbro sills that are widespread in the central part of the Oregon Coast Range (Snavely and Wagner, 1961; MacLeod, 1969) are not present in the Cascade Head area. The Cascade Head area is the last segment of the Oregon Coast to receive detailed geologic mapping. Increased logging operations in the 1970's and 1980's created numerous new roadcut exposures and access to exposures in stream beds. More importantly, microfossil biostratigraphic control, available since 1970, based upon foraminifer determinations by W.W. Rau and nannofossil determinations by David Bukry provided critical information on stratigraphic succession as well as on depositional environments of the deep water (bathyal) siltstone units present in much of the Cascade Head area. These paleontologic data also permitted correlations with other sedimentary sequences mapped in the Newport Embayment and in the Tillamook Highlands as well as in western Washington. New 7.5-minute topographic maps and aerial photographs which became available in the late 1980's provided detailed topography which can be related to the distribution of thick sills and broad landslide areas, as well as a precise geographic relationship of geologic observations in this densely forested and brush-covered terrain. New geographic information systems (GIS) technology has produced a digitized color map of the Cascade Head area that combines the four 7.5-minute quadrangles that previously were open-filed as separate black and white 7.5-minute quadrangles (Snavely and others, 1990; 1990a; 1991; 1993). The tectonic framework and stratigraphic architecture presented on the map of the Cascade Head area was obtained by classic geologic field methods. This information could have been obtained only through detailed observation and sampling along stream beds, road cuts, and outcrops. Remote sensing techniques were of minor help in unraveling the geology in this poorly exposed and complex terrain, a terrain that characterizes much of the Oregon and Washington Coast Ranges.

Oregon↗