USGS Science⌕ Search

Geology topics

David W. Pollock

Publications and source records attributed to David W. Pollock.

10 recordsLinked to original sources
USGS2016

User guide for MODPATH Version 7—A particle-tracking model for MODFLOW

MODPATH is a particle-tracking post-processing program designed to work with MODFLOW, the U.S. Geological Survey (USGS) finite-difference groundwater flow model. MODPATH version 7 is the fourth major release since its original publication. Previous versions were documented in USGS Open-File Reports 89–381 and 94–464 and in USGS Techniques and Methods 6–A41. MODPATH version 7 works with MODFLOW-2005 and MODFLOW–USG. Support for unstructured grids in MODFLOW–USG is limited to smoothed, rectangular-based quadtree and quadpatch grids. A software distribution package containing the computer program and supporting documentation, such as input instructions, output file descriptions, and example problems, is available from the USGS over the Internet ( http://water.usgs.gov/ogw/modpath/) .

Open-File Report↗
USGS2015

Extending the MODPATH algorithm to rectangular unstructured grids

The recent release of MODFLOW-USG, which allows model grids to have irregular, unstructured connections, requires a modification of the particle-tracking algorithm used by MODPATH. This paper describes a modification of the semi-analytical particle-tracking algorithm used by MODPATH that allows it to be extended to rectangular-based unstructured grids by dividing grid cells with multi-cell face connections into sub-cells. The new method will be incorporated in the next version of MODPATH which is currently under development.

Ground Water↗
USGS2012

User guide for MODPATH version 6—A particle-tracking model for MODFLOW

MODPATH is a particle-tracking post-processing model that computes three-dimensional flow paths using output from groundwater flow simulations based on MODFLOW, the U.S. Geological Survey (USGS) finite-difference groundwater flow model. This report documents MODPATH version 6. Previous versions were documented in USGS Open-File Reports 89-381 and 94-464. The program uses a semianalytical particle-tracking scheme that allows an analytical expression of a particle's flow path to be obtained within each finite-difference grid cell. A particle's path is computed by tracking the particle from one cell to the next until it reaches a boundary, an internal sink/source, or satisfies another termination criterion. Data input to MODPATH consists of a combination of MODFLOW input data files, MODFLOW head and flow output files, and other input files specific to MODPATH. Output from MODPATH consists of several output files, including a number of particle coordinate output files intended to serve as input data for other programs that process, analyze, and display the results in various ways. MODPATH is written in FORTRAN and can be compiled by any FORTRAN compiler that fully supports FORTRAN-2003 or by most commercially available FORTRAN-95 compilers that support the major FORTRAN-2003 language extensions.

Techniques and Methods↗
USGS2009

U.S. Geological Survey Groundwater Modeling Software: Making Sense of a Complex Natural Resource

Computer models of groundwater systems simulate the flow of groundwater, including water levels, and the transport of chemical constituents and thermal energy. Groundwater models afford hydrologists a framework on which to organize their knowledge and understanding of groundwater systems, and they provide insights water-resources managers need to plan effectively for future water demands. Building on decades of experience, the U.S. Geological Survey (USGS) continues to lead in the development and application of computer software that allows groundwater models to address scientific and management questions of increasing complexity.

Fact Sheet↗
USGS2006

A graphical modeling tool for evaluating nitrogen loading to and nitrate transport in ground water in the mid-Snake region, south-central Idaho

A flow and transport model was created with a graphical user interface to simplify the evaluation of nitrogen loading and nitrate transport in the mid-Snake region in south-central Idaho. This model and interface package, the Snake River Nitrate Scenario Simulator, uses the U.S. Geological Survey's MODFLOW 2000 and MOC3D models. The interface, which is enabled for use with geographic information systems (GIS), was created using ESRI's royalty-free MapObjects LT software. The interface lets users view initial nitrogen-loading conditions (representing conditions as of 1998), alter the nitrogen loading within selected zones by specifying a multiplication factor and applying it to the initial condition, run the flow and transport model, and view a graphical representation of the modeling results. The flow and transport model of the Snake River Nitrate Scenario Simulator was created by rediscretizing and recalibrating a clipped portion of an existing regional flow model. The new subregional model was recalibrated with newly available water-level data and spring and ground-water nitrate concentration data for the study area. An updated nitrogen input GIS layer controls the application of nitrogen to the flow and transport model. Users can alter the nitrogen application to the flow and transport model by altering the nitrogen load in predefined spatial zones contained within similar political, hydrologic, and size-constrained boundaries.

Scientific Investigations Report↗
USGS1995

Effect of seasonal and long-term changes in stress on sources of water to wells

The source of water to wells is ultimately the location where the water flowing to a well enters the boundary surface of the ground-water system . In ground-water systems that receive most of their water from areal recharge, the location of the water entering the system is at the water table . The area contributing recharge to a discharging well is the surface area that defines the location of the water entering the groundwater system. Water entering the system at the water table flows to the well and is eventually discharged from the well. Many State agencies are currently (1994) developing wellhead-protection programs. The thrust of some of these programs is to protect water supplies by determining the areas contributing recharge to water-supply wells and by specifying regulations to minimize the opportunity for contamination of the recharge water by activities at the land surface. In the analyses of ground-water flow systems, steady-state average conditions are frequently used to simplify the problem and make a solution tractable. Recharge is usually cyclic in nature, however, having seasonal cycles and longer term climatic cycles. A hypothetical system is quantitatively analyzed to show that, in many cases, these cyclic changes in the recharge rates apparently do not significantly affect the location and size of the areas contributing recharge to wells. The ratio of the mean travel time to the length of the cyclic stress period appears to indicate whether the transient effects of the cyclic stress must be explicitly represented in the analysis of contributing areas to wells. For the cases examined, if the ratio of the mean travel time to the period of the cyclic stress was much greater than one, then the transient area contributing recharge to wells was similar to the area calculated using an average steady-state condition. Noncyclic long-term transient changes in water use, however, and cyclic stresses on systems with ratios less than 1 can and do affect the location and size of the areas contributing recharge to wells.

Water Supply Paper↗
USGS1993

Factors affecting areas contributing recharge to wells in shallow aquifers

The source of water to wells is ultimately the location where the water flowing to a well enters the boundary surface of the ground-water system. In ground-water systems that receive most of their water from areal recharge, the location of the water entering the ground-water system is at the water table. The area contributing recharge to a discharging well is the surface area that defines the location of the water entering the ground-water system at the water table that flows to the well and is eventually discharged from the well. The calculation of areas contributing recharge to wells is complex because flow paths in ground-water systems change in response to development, and the aquifer material in ground-water systems is heterogeneous and is hidden from direct observation . Hypothetical experiments were undertaken to show the complexities in the delineation of areas contributing recharge to wells. Four different 'cases' are examined to demonstrate the effect of different conceptualized aquifer frameworks on deterministically calculated areas contributing recharge. The main conclusion drawn from the experiments is that, in order to understand the cause and effect relations that affect the quality of water derived from wells, the importance and nature of the variability in the ground-waterflow system must be considered and accounted for in any efforts to 'protect' the water supply.

Water Supply Paper↗
USGS1989

Documentation of computer programs to compute and display pathlines using results from the U.S. Geological Survey modular three-dimensional finite-difference ground-water flow model

A particle tracking post-processing package was developed to compute three-dimensional path lines based on output from steady-state simulations obtained with the U.S. Geological Survey modular 3-dimensional finite difference groundwater flow model. The package consists of two FORTRAN 77 computer programs: (1) MODPATH, which calculates pathlines, and (2) MODPATH-PLOT, which presents results graphically. MODPATH uses a semi-analytical particle tracking scheme. The method is based on the assumption that each directional velocity component varies linearly within a grid cell in its own coordinate direction. This assumption allows an analytical expression to be obtained describing the flow path within a grid cell. Given the initial position of a particle anywhere in a cell, the coordinates of any other point along its path line within the cell, and the time of travel between them, can be computed directly. Data is input to MODPATH and MODPATH-PLOT through a combination of files and interactive dialogue. Examples of how to use MODPATH and MODPATH-PLOT are provided for a sample problem. Listings of the computer codes and detailed descriptions of input data format and program options are also presented. (Author 's abstract)

Open-File Report↗