Geology topics

David Itter

Publications and source records attributed to David Itter.

5 recordsLinked to original sources

USGS2022

Scientific results of the Hydrate-01 Stratigraphic Test Well Program, Western Prudhoe Bay Unit, Alaska North Slope

The United States Department of Energy, the MH21-S Research Consortium of Japan, and the United States Geological Survey are collaborating to enable gas hydrate scientific drilling and extended-duration reservoir response testing on the Alaska North Slope. To feasibly execute such a test, a location is required that is accessible from existing roads and gravel pads and that can be occupied without disrupting ongoing industry operations. A review of potential locations meeting these criteria determined the likely occurrence of gas hydrate in two fine-grained marginal-marine sands of Tertiary age in the vicinity of the inactive “Kuparuk State 7-11-12” exploration pad in the western Prudhoe Bay Unit (PBU). Existing well and seismic data for that site were insufficient to preclude the potential for free gas occurrence within the deeper (and most prospective) target sand. Therefore, with support from the PBU Working Interest Owners, Alaska Department of Natural Resources, and Petrotechnical Resources Alaska, the Hydrate-01 Stratigraphic Test Well (STW) was drilled in December 2018 to confirm the suitability of the site for future gas hydrate scientific testing. The Hydrate-01 well was successfully drilled to −3290 ft (1003 m) subsea vertical depth at a bottom hole location of approximately 900 ft (∼275 m) east of the surface location. The drilling program featured acquisition of a full suite of logging while drilling data, the collection of side-wall pressure cores, and the installation of distributed temperature and distributed acoustic sensor fiber-optic cables. The log data acquired confirmed the occurrence of gas hydrate at high saturation in two target sands. Integrated evaluation of log and sidewall core data provide petrophysical and geomechanical property information that allow for potential reservoir response to depressurization to be simulated. The deeper “B1 sand” is deemed to be most favorable for reservoir response testing as a result of confirmed gas hydrate occurrence in sediments of high intrinsic permeability, location within 100 ft (30 m) of the base of gas hydrate stability, and minimal risk for direct communication with permeable water-bearing (hydrate-free) zones. The shallower “D1 sand” provides a secondary target that is differentiated by colder in situ temperatures and the interpreted direct hydraulic communication to a lower section of non-hydrate-bearing, water-saturated sand. The Hydrate-01 log data also confirm the occurrence of at least one sub-seismic fault in close proximity to the B1 sand reservoir. To better image the distribution of the gas-hydrate-bearing reservoir sections and associated faults, a three-dimensional (3D) vertical seismic profile was conducted in early 2019 using the distributed acoustic sensors installed as part of the Hydrate-01 STW completion. Detailed two-dimensional (2D) and 3D geologic models have been constructed to enable numerical simulations to inform the planning for potential future scientific tests of reservoir response to depressurization at the site.

Alaska↗

USGS2022

Planning and operations of the Hydrate 01 Stratigraphic Test Well, Prudhoe Bay Unit, Alaska North Slope

The National Energy Technology Laboratory, the Japan Oil, Gas and Metals National Corporation, and the U.S. Geological Survey are leading an effort to conduct an extended gas hydrate production test in northern Alaska. The proposed production test required the drilling of an initial stratigraphic test well (STW) to confirm the geologic conditions of the proposed test site. This well was completed in January 2019 in cooperation with the Prudhoe Bay Unit Working Interest Owners. The Prudhoe Bay Unit Hydrate-01 STW was spudded on 10-December-2018. Downhole data acquisition was completed on 25-December-2018, and the rig was released on 01-January-2019. The Hydrate-01 STW was drilled in two sections, including the surface hole that was drilled to a depth of 2248 ft measured depth (MD) (685 m MD) and cased, and the production hole section that was drilled to a depth of 3558 ft MD (1084 m MD) and also cased. A thermally chilled mineral-oil-based mud was used in the main (production) hole section of the well to maintain wellbore stability and quality of the wellbore acquired data. The primary wellbore data were acquired using logging-while-drilling tools. A sidewall pressure core system was also deployed to gather grain size and other data needed for the design of the future production test wells. In addition to confirming the geologic conditions at the test site, the Hydrate-01 STW was designed to serve as a monitoring well during future field operations. Therefore, two sets of fiber-optic cables, each including a bundled distributed acoustic sensor (DAS) and a distributed temperature sensor (DTS), were clamped to the outside of the production casing and cemented in place. In March 2019, the project team acquired three-dimensional (3D) DAS vertical seismic profiling data in the Hydrate-01 STW. Temperature surveys were also acquired with the DTS as deployed in the Hydrate-01 STW during the completion of the well and nearly continuously since March-2019.

Alaska↗

USGS2020

Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well: Technical results

The Hydrate-01 Stratigraphic Test Well was drilled in December 2018 to confirm that a seismically-identified location within the western Prudhoe Bay Unit might be suitable for extended-duration scientific production testing. The well tested two primary targets: the deeper Unit B is highly favorable due to optimal reservoir temperature and minimal observed risk for direct communication with permeable, hydrate-free water-bearing zones. The shallower Unit D provides a secondary target and opportunity to assess additional scientific and operational issues.

Alaska↗

USGS2020

Design and operations of the Hydrate 01 Stratigraphic test well, Alaska North Slope

The National Energy Technology Laboratory, the Japan Oil, Gas and Metals National Corporation, and the U.S. Geological Survey are leading an effort to conduct an extended gas hydrate production test in northern Alaska. The proposed production test required the drilling of an initial stratigraphic test well (STW) to confirm the geologic conditions of the proposed test site. This well was completed in December 2018 in cooperation with the Prudhoe Bay Unit Interest Owners. With the success of the STW, the project leadership group is developing plans to drill a geologic data well and a production test well. Drilling plans for the STW were advanced in late 2018. The Prudhoe Bay Unit Hydrate-01 well was spudded on 10-December-2018. Downhole data acquisition was completed on 25-December-2018 and the rig was released on 01-January-2019. The STW was drilled in two sections. The surface hole was drilled to a depth of 2248 ft (MD, measured depth) and cased, and the “production hole section” was drilled to a depth of 3558 ft (MD) and also cased. A thermally chilled mineral-oilbased mud was used to maintain drillhole stability and quality of the borehole acquired data. The primary borehole data were acquired using a suite of Schlumberger logging-while-drilling tools. To gather grain size and other data needed to inform the design of the production test well, sidewall pressure cores were collected using Halliburton’s CoreVault tool. In addition to confirming the geologic conditions at the test site, the Hydrate-01 well was designed to serve as a monitoring well during future field operations. Therefore, two sets of fiber optic cables, each including bundled Distributed Acoustic Sensors (DAS) and Distributed Temperature Sensors (DTS), were clamped to the outside of the well casing and cemented in place. In March 2019, the project team worked with SAExploration to acquire 3D DAS Vertical Seismic Profiling (VSP) data in the Hydrate-01 well, which was the largest 3D DAS-VSP ever conducted. Additionally, since the December 2018 completion of the STW, several borehole temperature surveys have been acquired with the DTS deployed in the Hydrate-01 well.

Alaska↗

USGS2019

Viable long-term gas hydrate testing site confirmed on the Alaska north slope

In December 2018, data acquired in a Stratigraphic Test Well drilled from the 7-11-12 pad in the western part of the Prudhoe Bay Unit, Alaska North Slope confirmed the occurrence of two high-quality reservoirs fully saturated with gas hydrate. The drilling was the initial phase of a planned, three-well program designed to conduct an extended duration test of the response to gas hydrate reservoirs to controlled depressurization. The Stratigraphic Test Well (formally “PBU Hydrate-01”) was operated by the PBU Operator BP Exploration, (Alaska), Inc. (BPXA) using the Parker 272 drilling rig (Figure 1) through a Drilling Services Agreement executed with Petrotechnical Resources of Alaska (PRA) in association with a contract between NETL and PRA. The science program executed by BPXA was developed over a two-year period through extensive discussions and scientific evaluation undertaken by NETL, the Japan, Oil, Gas, and Metals, National Corporation (JOGMEC), the U.S. Geological Survey (USGS), and PRA. The effort also benefitted greatly from the support of the Alaska Department of Natural Resources (ADNR) and the PBU Working Interest Owners (WIOs).

Alaska↗